Publicidad
Idiomas disponibles
Idiomas disponibles
WARNINGS AND SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS — this manual contains important
safety instructions. Do not operate the system unless you have
read and understood this manual. REDARC recommends that the
TVMS Rogue be installed by a suitably qualified person. It is the
installer's responsibility to ensure that their installation complies with
any applicable legal and regulatory requirements.
Disclaimer: REDARC accepts no liability for any injury, loss or
property damage which may occur from the improper or unsafe
installation or use of its products.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
When using this product, basic precautions should always be
followed, including the following:
1.
These products should not be used for any medical purposes,
life sustaining equipment, safety applications, or any application
where equipment failure can cause injury, death, fires or any
other hazard.
2.
Do NOT put fingers or hands into the product.
3.
Do NOT use the TVMS Rogue if damaged or modified. Damaged
or modified products may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
4.
No user serviceable parts inside. Do NOT attempt servicing this
product.
5.
Risk of explosive gases: Working in the vicinity of a battery
is dangerous. Batteries may generate explosive gases during
normal operation. Prevent flames and sparks, and provide
adequate ventilation especially during charging.
6.
To reduce risk of battery explosion, follow these instructions and
those published by the battery manufacturer and manufacturer
of any equipment you intend to use in vicinity of the battery.
PERSONAL PRECAUTIONS
7.
Consider having someone close-by to come to your aid if you
are working near a lead-acid battery.
8.
Have plenty of fresh water and soap nearby in case battery acid
contacts skin, clothing, or eyes.
9.
Wear complete eye protection and clothing protection. Avoid
touching eyes while working near battery. If battery acid
contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately flood eye with running
cold water for at least 10 minutes and get medical attention
immediately.
10.
Do NOT drop metal tools onto a vehicle battery. Doing so might
cause the battery to spark or might short-circuit the battery or
other electrical parts, which may cause an explosion.
11.
NEVER smoke or allow a spark or flame in vicinity of battery or
engine.
12.
Remove personal metal items such as rings, bracelets,
necklaces, and watches before working with a vehicle battery. A
vehicle battery can produce a short-circuit current high enough
to weld a ring or the like to metal, causing a severe burn.
13.
Have servicing performed by a qualified repair person using only
identical replacement parts. This will ensure that the safety of
the product is maintained.
14.
RISK OF FIRE — Do NOT install this product in the same
compartment where flammable substances are stored, such
as petrol/gasoline or Liquefied Petroleum Gas (LPG). Incorrect
handling or disassembly/reassembly may result in a risk of fire.
Any attempt to disassemble/reassemble the TVMS Rogue, or
make unapproved repairs or modifications will void the warranty
and the user's authority to operate the TVMS Rogue.
15.
DO NOT expose the TVMS Rogue to temperatures beyond the
published limits.
4
16.
DO NOT operate the TVMS Rogue beyond the published
ratings. Doing so may result in damage to the TVMS Rogue, fire,
explosion and burns/personal injury.
17.
If any mechanism or part of the TVMS Rogue becomes broken
or damaged, discontinue use immediately.
18.
Use suitable Personal Protective Equipment (PPE) when
operating power tools.
CAUTION
19.
The system should not be used by persons under the age of 18,
or those with reduced physical, sensory or mental capabilities
or lack of experience and knowledge unless they are supervised
and under instruction.
20.
Power sources must NOT be connected to the TVMS Rogue
Outputs (C/D). Connecting batteries or power supplies to the
Outputs (C/D) may damage the TVMS Rogue.
21.
Selecting the wrong cable or fuse size could result in harm
to the installer or user and/or damage to the battery or other
equipment installed in the system. The installer is responsible
for ensuring that the correct cable type and fuse sizes are used
when installing the TVMS Rogue.
22.
Do NOT modify the Power Wiring Loom cable while it is plugged
into the Main Unit.
23.
The chassis/ground connection should be made away from
batteries and fuel lines.
24.
Ensure all connection surfaces are clean, paint-free, and
protected against corrosion.
25.
Cabling must be installed in protected areas away from heat
sources, sharp objects or over/through parts of the vehicle
that move during operation or maintenance. Supplementary
protection such as conduit may be required, especially when
installing or routing in the engine bay.
26.
Do NOT use this product to control safety critical devices or
those that could cause harm if operated remotely (for example
fume exhaust fans or lifters). Only operate devices with moving
parts when you have a clear line of sight to the moving parts.
27.
NEVER connect the TVMS Rogue output negative to chassis
ground. Either connect the TVMS Rogue output negative to the
negative of a load OR connect chassis ground to the negative of
a load and leave the TVMS Rogue output negative unconnected.
28.
The TVMS Rogue outputs are internally software-fused at 10 A. If
wiring to a circuit that has a lower current capability e.g. thinner
wire, a suitable fuse must be fitted to protect the circuit and
prevent damage/fire.
NOTICE
29.
Do NOT parallel the outputs on the Output Loom — it could
cause the TVMS Rogue to not function as expected and may
trigger a Fault.
30.
Insulate the ends of individual unused wires to prevent them
from shorting. DO NOT heatshrink/tape multiple unused wires
together as a single bundle. Heatshrink/electrical tape must
fully-encapsulate bare wires and be securely shrunk/adhered
onto the wires.
Publicidad
