Descargar Imprimir esta página

TESY ESP32 Instrucciones De Uso página 33

Módulo de comunicación inalámbrico incorporado (wi-fi) para un convector eléctrico

Publicidad

5.
Statistics
- gives information about the operation of the device, with the
option to choose between daily, monthly and annual activity.
6.
Rename device - change the device name
7.
Add to group - add the device to a group
- press the button "Create new group"
- set a name for the group, confirm with the button "Save"
- to add devices to the group, press "+"
- to correct or delete, press the button "
„Delete" button
, a „delete" sign appears next to each device in the group,
respectively a „correct" sign, when you press the „Edit" button
Upon successful completion of the process, a section with the groups you have
created is displayed on the main screen, as well as a list of devices. Below each group
there is an „Edit group" button, where you can remove devices from the group by
clicking the „delete" sign
.
8.
Device information
- Provides information about the device software
9.
Settings
- has access to change settings for:
Mode "Eco" - see QUICK START D4
TROUBLESHOOTING
Prior to contacting the Customer Service Center, please check the items in the table below.
PROBLEM
Unsuccessful connecting to the home Wi-Fi network (wireless
connection)
The convector does not appear in the application
When you search for the appliance from your Smart device and the
convector is not visible
The convector is properly connected but does not work.
If the inbuilt wireless module does not see the wireless router
(modem)
When attempting at restoring the factory settings, the appliance
does not restore the factory settings
Your appliance could not reconnect to the wireless router (modem)
Upon opening the mobile application, your appliance is inactive
English
.
" - when you press the
.
10.
For full instructions for use and store, follow the link below:
https://tesy.com/products/heating-appliances/electric-panel-convectors
Check if the modem is switched on.
If you use portable computer, make sure that that the wireless connection switch on the
front, at the side or at the back of the portable computer is in "on" mode.
Make sure you type your home network password correctly
Wait for about a minute and check again if connection is established.
Your wireless network should be 2.4Ghz
Allow access to the location of the device with which you connect to the appliance
Check if your router is connected to the Internet.
The convector has to be connected to a wireless router (modem) in your home (office).
Check if the convector is properly connected to the wireless router (modem).
Repeat the steps for connecting to the appliance
Go near the convector
Try to find it again by pressing the "Continue" button
Check the device menu if the Wi-Fi network is "on"
Make sure your device is connected to a wireless Wi-Fi network
Restore your appliance to the factory settings
Close all VPN connections on your device
Turn on only one Tesy appliance
Check if the appliance is connected to the electrical grid
Restart the application.
Place the convector in a position with the wireless router (modem) in sight.
Use additional wireless modem to boost the signal of the wireless router (modem)
Try repeating the factory reset procedure again
Leave the appliance unplugged for 30 minutes
You have a new wireless router (modem). Please set the convector again.
A factory reset has been performed. Please set the convector again.
Switch manually from Local to Internet control from the device menu
Not assigned product to the home Wi-Fi network
Wait 30 seconds, if not active again, clear the cache files on your mobile device
Mode "Comfort"- see QUICK START D5
Mode "Sleep" - see QUICK START D6
Mode "Delayed start" - see QUICK START D7
Change Wi-Fi network - select a Wi-Fi network from the drop-down menu, enter
the password of the new network and save the settings
Sensor temperature correction - selection of correction in the range of - 4°C to +
4°C, as well as the power of the convector from the drop-down menus
World clock - is set automatically when you add the device by taking the data
from the settings of the phone you are operating with. In this menu there is an
option to change the time zone, current date and current time.
Delete the device from your account
TESY's team reserves the possibility to change and add new functions in the
products with inbuilt Wi-Fi module, as well as to change the instructions in
accordance with the new versions of the software.
SOLUTION
Operation and Storage Manual of Panel Heater
EN
33

Publicidad

loading