Publicidad
Idiomas disponibles
Idiomas disponibles
BACK LIGHT
You can set the desired
brightness
mode.
(Refer to "Back Light Setting"on
page 22.)
COLOR TEMR
You can adjust color temperature
("NORMAU', "WARM",
"COOU').
(Refer to "Color Temperature"
on page 22.)
DTVCC
In addition
to the basic closed caption
described
on page 18, DTV has its own closed caption
called
DTVCC.
(Refer to "DTV Closed Caption"
on page 20.)
PC SETTING
You can adjust the position,
stability
and clarity of the
PC screen.
This menu will appear only in PC mode, and can only
be set when the unit detects
the PC input signal.
(Refer to"PC Settings"on
page 26.)
_Auto
Channel
Scan
If youswitchwires(e.g.,betweenantennaandCAW)or if you movethe
unit toa differentareaafter the initialsetting,or if yourestore the DTV
channel y oudeleted,youwill needto perform auto channel s can.
Before youbegin:
Make sureif the unit isconnectedto antenna or cable.
1
Press [SETUP] to display the main menu.
2
Use [Cursor •
/ V] to select"CHANNEL
SETUP",
then press [ENTER].
e.g.) digital TV mode
or
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHiP SETUP
LANGUAGE
[ENGLISH]
CAPTION
[OFF]
RACK LIGHT
[RREGHTj
COLOR TEMR
[NORMAL]
DWOC
3
Use [Cursor •
/ V] to select your desired preset type,
then press [ENTER].
e.g.) digital TV mode
or
-CHANNELSETUP-
ADD_)ELETE(DW)
_- AUTO PRESETCH(UT_
AUTO PRESETCH(W_DT_
AUTO PRESETCH(GATV]
! CAW takes appr0x 5Omin
• When aerial antenna
is connected,
select "AUTO PRESET CH(TV)", "AUTO PRESET CH(DTV)"
or"AUTO PRESET CH(TV/DTV)".
• When connected
to CATV, select
"AUTO PRESET CH (CATV)'t
• Scanning
and memorizing
the channels automatically
start.
e.g.) digital TV mode
D25
AUTO PRESETCH(DTV)
I J
J
J
• When the scanning
and memorizing
are completed,
the lowest memorized
channel
will be displayed.
• When you selected "AUTO PRESET CH(TV/DTV)", the
lowest memorized
analog channel
will be displayed
when the scanning
and memorizing
are completed.
If there is no analog channel,
the lowest memorized
digital
channel
will be displayed.
No te:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel scan,
the setting will be canceled.
• When no channel can be received by auto channel scan,
"NO TV SIGNALS"will be displayed on the TV screen.
• Channel settings will be saved even if the power fails.
• Ifyou have Spanish or French menus and need English,
press [SETUP]. Use[Cursor A iV] to select "IDIOMA"
or "LANGAGE"Press[ENTER]to select "ENGLISH". P ress
[SETUP] to remove the main menu.
• With regard only to the digital channel, even after the
scanning is complete if you unplug the ACpower cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.
[] Language
Selection
Youcanchoose English, S panish, or French asyouron-screen language.
1
Press [SETUP] to display the main menu.
Use [Cursor•
IV]
to select"LANGUAGE",
then press [ENTER] repeatedly
to change the setting.
e.g.) digital TV mode
or
- W SETUP -
PICTURE
CHANNELSETUP
V-CHIP SETUP
LANGUAGE
[ENGUSR]
CAPTION
[OFF]
SACK LIGHT
[BRIGHT]
COLOR TEMP
[NORMA_
UTVCC
Press [SETUP] to exit.
EN
Publicidad
