Publicidad
~
n---,
J10
""l
11
J 2 2
~21
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
f~--~
1 8 - - - - ~
1 7 - - - - - - - ~
Color
Purple/ black
Green
I
black
Gray
I
black
White
/
black
NC
Purple
/
black
Green
I
black
Gray
I
black
White
/
black
Yellow
Yellow
Purple
Green
Gray
White
Blue/white
Purple
Green
Gray
White
Black
Black
function
Audio Input, Rear
right(-)
Audio
Input,
rear left(-)
Audio Input, front right(-)
Audio
Input,
front
left (-)
Audio
Output,
rear right(-)
Audio
Output,
rear left(-)
Audio
Output,
front
right(-)
Audio
Output,
front left(-)
Battery,
Positive leads
Battery,
Positive leads
Audio Input, Rear
right(+)
Audio Input, rear left(+)
Audio Input, front right(+)
Audio Input, front left(+)
Remote on
Audio Output,
rear
right
( +)
Audio
Output,
rear left(+)
Audio
Output,
front right ( +)
Audio Output, front left(+)
Ground
Ground
Fig.1
CONNECTIONS (Fig. 1)
Before making connections, be sure to turn the power off to all audio
components.
Connect the
yellow battery lead from the amp directly to the positive(+) terminal of the vehicle's battery. Do
not connect this
lead
to the fuse block.
it,
CAUTION
♦
Caution on connection terminals/parts
•
Keep electrically conductive objects away from the unit's terminals/parts (power
terminals,
fuses, speaker output terminals, RCA connectors, etc.). Doing so prevents a possible short
circuit and damage
to
the unit.
•
Use appropriate electrical
source.
The person installing this
will
choose the appropriate
electrical
source.
To prevent external noise from entering the audio system.
•
Locate the unit and route the leads at least 10 cm (3-15/16") away from the car
harness.
•
Keep the battery power leads as far away from other leads as possible.
•
Connect the ground lead securely to a bare metal spot
(remove
any paint or grease if necessary) of the car
chassis.
•
Your Alpine dealer knows best about noise prevention
measures so consult your dealer for further
information.
CD
Input/Output/Power Connector
(2)
lnput/Output/PowerWire Harness
®
Speaker Output Leads
Be sure to observe correct speaker output connections
in
the
system.
Connect the positive
output(+) to the positive speaker terminal and the negative output(-) to the negative speaker
terminal.
Note:
•
Do not connect speaker leads together or to chassis
ground.
®
Input Signal Leads
There are two
options:
a) RCA Input Jacks
Connect these jacks to the line out leads on your head
unit,
you may or may not require
extension
cable.
b) Speaker Level Inputs
Note:
Cut off the RCA
jacks,
then connect the correct corresponding speaker outputs from the
head unit directly to these twisted pair
wires.
•
For the
•speaker
Level Input
System" setting,
connecting the Remote Turn-On Lead is not
required due to the
"REMOTE
SENSING" function of this product. However, the
"REMOTE
SENSING" function may not work depending on the signal source
connected.
In such a case,
connect the Remote Turn-On Lead to an incoming power supply wire (accessory power) in
the ACC
position.
@
Ground Lead (Black)
Connect this lead securely to
a
clean, bare metal spot on
the vehicle's chassis. Verify this point to be a true ground by checking for continuity between
that point and the negative (-) terminal of the vehicle's battery. Ground all your audio
components to the same point on the chassis to prevent ground loops.
®
Battery Lead (Yellow)
Connect battery lead directly to BATT +
Be sure to add a 20A fuse (sold separately) as close as possible to the battery's (+) terminal.
(/)
Remote Tum-On Lead (Blue/White)
Connect this lead to the remote turn-on or power antenna (positive
trigger,
(+) 12V only) lead
of your head unit.
Publicidad
