Bosch GWS Professional 30-230 B Manual Original página 24

24 | English
a)
(20) Cutting disc
a)
(21) Diamond cutting disc
(22) Disc brush (dia. 22.22 mm)
a)
(23) Disc brush (M14)
(24) Handle (insulated gripping surface)
(25) Grinding spindle
a)
(26) Hand guard
a)
(27) Rubber sanding pad
a)
(28) Abrasive disc
Technical Data
Angle grinder
Article number
Rated power input
A)
Rated no-load speed min
Max. grinding disc dia- mm
meter/rubber backing pad
diameter
Grinding spindle thread
Max. thread length of mm
grinding spindle
KickBack Control
Restart protection
Soft start
Run-out brake
Status indicator (LED)
PROtection switch
B)C)
Weight
Protection class
A) Rated no-load speed for the selection of appropriate application tools in accordance with EN IEC 62841-2-3. The actual no-load speed
must not exceed the rated no-load speed and is therefore lower.
B) Depends on protective guard ((17), (18), (8), (9), (19)), auxiliary handle ((5), (6)) and extraction guard (34) in use
C) Weight without mains connection cable and without mains plug
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Values can vary depending on the product, scope of application and environmental conditions. To find out more, visit
www.bosch-professional.com/wac.
Noise/Vibration Information
Noise emission values determined according
to EN IEC 62841-2-3.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 97 dB(A); sound power
level 105 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN IEC 62841-2-3:
Surface grinding (roughing):
2 2
a = 5.0 m/s , K = 1.5 m/s ,
h
Disc sanding:
2 2
a = 2.7 m/s , K = 1.5 m/s ,
h
1 609 92A 9AU | (09.04.2024)
a)
GWS 30-180 B GWS 30-230 B GWS 30-180 PB GWS 30-230 PB GWS 30-230 B
3 601 HG0 0.. 3 601 HG1 0..
W 2800 2800
–1
8500 6500
180
M 14 M 14
25
●
●
●
●
●
–
kg 5,7–7,5 5,9–8,4
/ II
a)
(29) Round nut
a)
(30) Cup brush
a)
(31) Open-ended spanner
a)
(32) Conical brush
a)
(33) Diamond annular cutter
(34) Extraction guard for cutting with a cutting guide
(35) Clamping flange
(36) O-ring
a) This accessory is not part of the standard scope of delivery.
3 601 HG0 1.. 3 601 HG1 1.. 3 601 HG1 0..
2800
8500
230 180
M 14
25 25
● ●
● ●
● ●
● ●
● ●
– ●
5,7–7,5
/ II / II
Cut-off grinding:
2 2
a = 4.4 m/s , K = 1.5 m/s .
h
Grinding thin metal sheets or other materials that tend to easily vi-
brate with a large surface area can cause the noise emission value to
increase by up to 15 dB. Suitable, heavy damping mats can reduce
the increased noise emissions. Increased noise emissions must be
taken into consideration, both for the risk assessment of the noise
output and for selecting suitable hearing protection.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ac-
a)
2800 2200
6500 6500
230 230
M 14 M 14
25 25
● ●
● ●
● ●
● ●
● ●
● –
5,9–8,4 5,9–8,4
/ II / II
Bosch Power Tools