Publicidad
Idiomas disponibles
Idiomas disponibles
Button
GB
1
2
3
4
5
6
7
8
9
0
Programming
Open the door and press and hold "1" on the number keyboard
for about 4 ~ 6 seconds, the buzzer will sound and the display
will show 'PROGRAM' to indicate you entered program mode.
Select the time with the 'Time Entry' button, the display will
show "00:00", select the requested time with the number key-
board. After that, select the power level. Press 'Power' button
first and then select the power level with the number key-
board as shown in below table (Defrost/10%/20%/30%/40%/
50%/60%/70%/80%/90%/100%). The display will show the se-
lected power. If you press again the same power level button,
the power will be back to set 100% power. Also, if no power
level button is set, the power will be default to 100%. After
setting the time, power and press the 'start' button to safe the
program. The display will show 'PROGRAM'. Close the door to
return to 'Ready mode'. If you want to cancel during program-
ming, press the 'Pause' button and the oven will return to the
'door open' mode and the program won't be saved.
Below a quick guide how to make a program of 1.25 minutes
at 70% power:
1. Open the door and press number button '1' for about 4 ~ 6
seconds, display will show 'PROGRAM'.
2. Press number button '3', display shows P003. After 2 seconds
the display will show the time related with the program ':30'.
3. Press the number buttons '1' '2' '5' to set the cooking time.
4. Press 'Power' button, and choose 7 on the number key-
board for power level 70%. The display will show '1:25 70'.
5. Press the 'Start' button. The program is now saved under
number keyboard '3'.
To overwrite the program repeat the steps above.
Note: Total programming time is limited to 60 minutes only.
Note: When the cooking time exceeds the maximum time the
microwave can operate (standard 60 minutes) three beeps will
be sound. This means you need to adjust the time before the
program can work.
Double and triple quantity (X2 or X3)
This microwave is equipped with a function to calculate the
amount of time needed when preparing a double or triple
quantity of food. Press the 'X2' or 'X3' button followed by the
program and the microwave double or triple the time you preset
and start the process. This function can only be used in combi-
10
Display time
Power
0:10
100%
0:20
100%
0:30
100%
0:45
100%
1:00
100%
1:30
100%
2:00
100%
2:30
100%
3:00
100%
3:30
100%
nation with a preset program.
Multi stage cooking
This function can be used during manual entry or program-
ming. The maximum number of stages is 3. To use this func-
tion first follow the steps under 'Manual entry'. After setting
the time and power of the first stage press 'Time Entry' button
again, the display shows "STAGE-2", now input the desired time
and power. If a third stage is needed, press 'Time Entry' button
once more, the display will show "STAGE-3", and input the de-
sired time and power. Now press the 'start' button to start the
microwave. Multi stage input is set in a same manner while in
programming mode. Bellow an example of how this could work:
1. Open the door and press and hold "1" on the number key-
board for 4 ~ 6 seconds, display will show "PROGRAM".
2. Press number button '3', display shows "P003". After 2 sec-
onds the display will show the time related with the pro-
gram (standard ':30').
3. Press the number buttons '1' '2' '5' to set the cooking time.
4. Press 'Power' button, and choose 7 on the number key-
board for power level 70%. The display will show "1:25 70".
5. To set the second stage press 'Time Entry' button for button
2- time entry button, the display will show "STAGE-2".
6. Press the number buttons '3' '3' '0' to input the time.
7. Press 'Power' button, and choose 5 on the number key-
board for power level 50%. The display will show "3:30 50".
8. Press the 'Start' button for button 5. The multi stage pro-
gram is now saved under number keyboard '3'.
Note: Total cooking time is limited to 60 minutes only.
Note: When multi stage cooking is active the microwave shows
the total time remaining of all stages.
How to set the U disk
1. Insert U disk to your PC or Mac, select the appropriate in-
staller package according to the computer system:
Flash Tune 1.1.3.exe is for Window.
Flash Tune 1.1.3.dmg is for Mac.
2. Click the icon after installation to open the FlashTune soft-
ware and click the Commercial MWO.
3. Complete the cooking time required for STAGE 1 of your cooking
cycle. The maximum time value of each stage is 60 minutes.
4. Select the % of power required for STAGE 1 .
5. Complete each stage of cooking. STAGE 1, 2 and 3 if appli-
cable. Update each menu item line by line. Key in the Min
and Sec, and choose Power of each STAGE of each line.
6. The auto recipe setup can be completed by either software
or microwave oven. Open the door and long press the num-
ber Key 1 when the power is on and the "PROGRAM" will be
shown on the display screen. Input the reset recipe number
and the recipe maybe set up by inputting number Key 1. The
number Key 0-9 are also available for changing the cooking
time. If the heat power is to be changed, press "power level"
key. For example, press Key 6 indicates 60% power level.
Finally press "Start" key to complete the operation.
How to Save Your Program File
1. To save your progress or add/edit menu items, click on File
and Save as. Name your file and save.
2. Your files are saved and can be opened and edited later.
And the saved files can be transferred to another comput-
Publicidad
