Allen + Roth HARTFORD WSLVCKJ Instrucciones De Ensamblaje página 6

ASSEMBLY INSTRUCTIONS
13. Using a stud finder (not included), locate the edges
of the wood studs. Find the center line of each stud
and draw a vertical reference line on the wall over
each one. Position installation template (R) at desired
location on wall.
Note: The bottom of the installation template (R) should
be no less than 31-1/2 in. from the floor.
Mark mounting holes with a pencil (not included) and
discard installation template (R). Drill 3/16 in. pilot
holes at marked locations. Then, with the beveled
edge facing up, attach the wall hanging cleats (I) with
large flat washers (JJ) and M8 x 2-1/2 in. lag bolts (II).
Hardware Used
M8 x 2-1/2 in. Lag Bolt
II
Large Flat Washer
JJ
14. With the help from another person, carefully hang the
unit from mounting cleats (H) & middle fixed Shelf (G)
onto wall hanging cleats (I).
Long Shelf Installation
Note: If long shelf (K) needs cut to fit inside your closet
space, cut only one side of the shelf and do not use a
hacksaw. It is recommended you hire an insured remodeler
for this type of installation.
15a. With a pencil, draw a level line at the desired mounting
location for long shelf (K).
15b. Using L-brackets (KK) as a guide, mark the screw hole
locations with a pencil.
15c. Drill 3/8 in. diameter pilot holes at least 2-1/2 in. deep
at marked locations, then insert wall anchors (RR) into
the holes until they are flush with the wall.
15d. Attach L-brackets (KK) to the wall using M4 x 38 mm
screws (UU) and to the long shelf (K) using M4 x 14
mm wood screws (VA).
Hardware Used
L-Bracket
KK
Wall Anchor
RR
M4 x 38 mm Screw
UU
M4 x 14 mm Wood Screw
VA
13
Wooden Stud
16 in.
I
40.6 in.
R
Minimum 31-1/2 in.
x 4
14
x 4
H
I
G
15
K
x 4
UU
x 8
x 8
x 8
10
ASSEMBLY INSTRUCTIONS
16. Attach long shelves (K) to left side panel (A) and
right side panel (B) with L-brackets (KK), securing
with M4 x 14 mm wood screws (VA).
JJ
Hardware Used
L-Bracket
II
KK
M4 x 14 mm Wood Screw
VA
I
JJ
17. If you intend to install the expandable pole, attach
wood supports (J) on the inside of upper left side
II
panel (A) and/ or upper right side panel (B) using
wood screws (FF).
Note: The expandable pole should be installed to the
middle of wood support (J). The 3 screws should be
attached to the slats of the upper left side panel (A)
and/ or upper right side panel (B).
Hardware Used
M3.5 x 12 mm Wood Screw
FF
Pole Installation
18a. Insert 22 mm metal poles (T) into 25 mm metal
poles (S).
18b. Using closed pole holders (YC) as a guide, mark
screw hole locations with a pencil.
18c. Drill 3/8 in. diameter pilot holes at least 2-1/2 in.
deep at marked locations, then insert drywall
anchors (not included) into the holes.
18d. Attach closed pole holders (YC) with M4 x 38 mm
zinc screws (ZZ).
18e. Insert 25 mm metal poles (S) into closed pole
holders (YC), securing with M4 x 15 mm
self-tapping screws (YY).
RR
Note: Drywall anchors are not required if installing into
a stud.
Hardware Used
KK
Closed Pole Holder
YC
VA
M4 x 15 mm Self-tapping Screw
YY
M4 x 38 mm Zinc Screw
ZZ
16
x 4
x 16
KK
17
B
J
x 12
J
A
18
T
S
YY
x 3 ZZ
Drywall Anchor
YC
x 3
x 9
11
K
VA
J
FF
YC