Publicidad
Idiomas disponibles
Idiomas disponibles
EXTENSION
CORDS
Grounded tools require a three wire extension cord.
As the distance from the supply outlet increases,
you must use a heavier gauge extension cord. Using
extension cords with inadequately sized wire causes
a serious drop in voltage, resulting in loss of power
and possible tool damage. Refer to the table shown
to determine the required minimum wire size.
The smaller the gauge number of the wire, the greater
the capacity of the cord. For example, a 14 gauge
cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make
up the total length, be sure each cord contains at
least the minimum wire size required. If you are using
one extension cord for more than one tool, add the
nameplate amperes and use the sum to determine
the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure
it is marked with the suffix "W-A" ("W" in Canada) to
indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and in
good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified
person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
For Extension Cords*
Nameplate Amps
25'
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
* Based on limiting the line voltage drop to five volts at 150%
of the rated amperes.
ASSEMBLY
WARNING
charging instructions, read the operator's man-
ual supplied with the charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
may be hazardous.
Extension Cord Length
50'
75'
100'
18
18
18
18
18
18
18
16
18
18
16
14
18
16
14
12
16
14
12
10
14
12
10
--
12
10
--
--
Recharge only with the
charger specified for the
battery. For specific
Always remove the bat-
tery pack any time the
tool is not in use.
Only use accessories
specifically recommend-
ed for this tool. Others
nserting/Removing Extension Cords to
I
Operate on AC Power
To operate the dust extractor on AC Power, plug in a
suitable extension cord into the dust extractor.
NOTE: When an extension cord is plugged into the
dust extractor, the dust extractor will automatically
run on AC power.
To disconnect the extension cord, press the Power
button to turn off the the dust extractor , then remove
the cord from the outlet.
Unpack accessories and parts from the tank by
unlatching the motor housing and pulling it up and
off the tank.
VACLINK™ is a wireless dust control technology that
allows a compatible tool and vacuum/dust extractor
(vacuum) to connect to each other.
A signal from the tool will turn the vacuum on and
off. The tool can be connected to one vac at a time.
The vacuum can be connected to multiple remotes
or tools at at time.
Pairing a VACLINK™ Remote
If the VACLINK™ remote is not connected to the dust
extractor, pairing can be setup by:
1. Insert battery packs into the dust extractor.
2. Press the VACLINK™ button on the dust extractor
and the remote until both LED's begin to flash. A
steady green light on both the dust extractor and
the remote will confirm that the unit is paired.
NOTE: Remote needs to be within close proximity
to ensure remote is receiving signal from the the
dust extractor. This procedure will time out after
30 seconds if the dust extractor is not paired and
will enter standby mode for inactivity.
150'
To confirm that the remote has paired with the dust
extractor successfully, press the VACLINK™ button
16
on remote and the VACLINK™ button on the dust
14
12
extractor will light. Multiple remotes can be paired to
12
one dust extractor.
--
Pairing a VACLINK™ Tool
--
Consult the VACLINK™ tool's manual for pairing to
--
the 0888-20.
1. Install a battery pack on the tool and connect the
vacuum to a power source.
2. Press and hold the pairing buttons on the tool and
vacuum each for >1 second.
VACLINK™ LED:
• Searching - flashing green
• Paired - solid green
3. See "Troubleshooting" if tool and vacuum do not
pair successfully.
4. To unpair, press and hold the pairing button on
the tool for >1 second.
VACLINK™ LED:
• Unpaired - off
Unpairing VACLINK™ from all connected devices
1. To remove/erase all paired devices from dust ex-
tractor, press and hold the VACLINK™ button on
the remote until the LED has a flashing red light.
2. Press and hold the VACLINK™ button on the dust
extractor until the LED has a flashing red light.
If the remote and the dust extractor are not paired
after 30 seconds, this procedure will time out and
enter standby mode for user inactivity.
5
VACLINK™
Publicidad
