Hikmicro RAPTOR Serie Guia De Inicio Rapido página 80

This equipment complies with IC RSS-102 radiation
exposure limits set forth for an uncontrolled
environment.
Safety Instruction
These instructions are intended to ensure that user
can use the product correctly to avoid danger or
property loss.
Laws and Regulations
Use of the product must be in strict compliance with
the local electrical safety regulations.
Transportation
Keep the device in original or similar packaging

while transporting it.
Keep all wrappers after unpacking them for future

use. In case of any failure occurred, you need to
return the device to the factory with the original
wrapper.
Transportation without the original wrapper may

result in damage on the device and the company
shall not take any responsibilities.
Do not drop the product or subject it to physical

shock. Keep the device away from magnetic
interference.
Power Supply
The input voltage for the device should meet the

Limited Power Source (5 VDC, 2 A) according to the
IEC61010-1 standard. Please refer to actual
products and technical specifications for detailed
information.
The power source should meet limited power

source or PS2 requirements according to IEC 62368-
1 standard.
Use the power adapter provided by qualified

manufacturer. Refer to the product specification for
detailed power requirements.
Make sure the plug is properly connected to the

power socket.
DO NOT connect multiple devices to one power

adapter, to avoid over-heating or fire hazards caused
by overload.
Battery
Improper use or replacement of the battery may

result in explosion hazard. Replace with the same or
equivalent type only. Dispose of used batteries in
conformance with the instructions provided by the
battery manufacturer.
Use the battery provided by qualified

manufacturer. Refer to the product specification for
detailed battery requirements.
Make sure the battery temperature is between 0°C

to 45°C (32°F to 113°F) when charging.
For long-term storage of the battery, make sure it

is fully charged every half year to ensure the battery
quality. Otherwise, damage may occur.
The built-in battery cannot be dismantled. Please

contact the manufacture for repair if necessary.
Batteries of improper size cannot be installed, and

may cause abnormal shutdown.
The battery cannot be charged with external

power source directly.
Confirm there is no flammable material within 2 m

of the charger during charging.
DO NOT place the battery near heating or fire

source. Avoid direct sunlight.
DO NOT place the battery in the reach of children.

DO NOT swallow the battery to avoid chemical

burns.
Maintenance
If the product does not work properly, please

contact your dealer or the nearest service center.
We shall not assume any responsibility for problems
caused by unauthorized repair or maintenance.
Wipe the device gently with a clean cloth and a

small quantity of ethanol, if necessary.
If the equipment is used in a manner not specified

by the manufacturer, the protection provided by the
device may be impaired.
Clean the lens with soft and dry cloth or wiping

paper to avoid scratching it.
It is recommended to reboot the device every 2

hours when using it to ensure the device
performance.
Using Environment
Make sure the running environment meets the

requirement of the device. The operating
temperature shall be -30 °C to 55 °C (-22 °F to
131 °F), and the operating humidity shall be 95% or
less, no condensing.
Place the device in a dry and well-ventilated

environment.
DO NOT expose the device to high

electromagnetic radiation or dusty environments.
DO NOT aim the lens at the sun or any other bright

light.
When any laser equipment is in use, make sure

that the device lens is not exposed to the laser
beam, or it may burn out.
Avoid equipment installation on vibratory surface

or places subject to shock (neglect may cause
equipment damage).
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Laser
When any laser equipment is in use,
make sure that the device lens is not
exposed to the laser beam, or it may
burn out. The laser radiation emitted from the device
can cause eye injuries, burning of skin or
inflammable substances. Before enabling the light
supplement function, make sure no human or
inflammable substances are in front of the laser
lens. Do not place the device where minors can
fetch it. The wavelength is 905 nm, and the max.
power output is less than 1.328 mW. According to
IEC 60825-1:2014 and EN 60825-1:2014+A11:2021,
this laser product is classified as Class 1 laser
product.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road,
Xixing Subdistrict, Binjiang District, Hangzhou,
Zhejiang 310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products
might be subject to export controls in various
countries or regions, including without limitation, the
United States, European Union, United Kingdom
and/or other member countries of the Wassenaar
Arrangement. Please consult your professional legal
or compliance expert or local government
authorities for any necessary export license
requirements if you intend to transfer, export, re-
export the thermal series products between different
countries.
78