Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Hold the power tool by insulated gripping surfaces
u
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
workpiece by your hand or against the body leaves it
unstable and may lead to loss of control.
Wait for the cutter to stop before setting the tool
u
down. An exposed rotating cutter may engage the surface
leading to possible loss of control and serious injury.
Keep the cutter sharp. Dull or damaged cutters may
u
cause the planer to swerve or stall under pressure. Always
use the appropriate type of cutter for the power tool.
Do not touch the workpiece or the cutter immediately
u
after operating the tool. They can become very hot.
Remove all nails and metal objects from the
u
workpiece before planning.
Always hold the tool with both hands and by the
u
handles provided.
Immediately disconnect the cable from the mains if it
u
is damaged or cut.
Warning! Contact with, or inhalation of dusts arising from
planing applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically
designed for protection against dust and fumes and ensure
that persons within or entering the work area are also
protected.
Safety of others
This tool can be used by children aged from 8 years and
u
above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction
concerning use of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance. Cleaning and
u
user maintenance shall not be made by children without
supervision.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
6
(Original instructions)
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
and noise
The declared vibration and noise emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method provided
by EN 62841 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration and noise emission value during
actual use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The vibration
and noise level may increase above the level stated.
When assessing vibration exposure to determine safety
measures, an estimation of vibration exposure should
consider, the actual conditions of use and the way the tool is
used, including taking account of all parts of the operating
cycle such as the times when the tool is switched off and
when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear Ear protection.
Electrical safety
#
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on
the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER service
centre in order to avoid a hazard
Using an extension cable
Always use an approved extension cable suitable for the
u
power input of this tool (see technical data). Before use,
inspect the extension cable for signs of damage, wear and
ageing. Replace the extension cable if damaged or
defective. When using a cable reel, always unwind the
cable completely.
Publicidad
