Publicidad
Idiomas disponibles
Idiomas disponibles
Intended use
The machine is intended for blowing and vacuuming.
Never use the machine for other purposes. Failure to do
so may cause injury.
Noise
The typical A-weighted noise level determined accord-
ing to EN50636-2-100:2014:
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
Sound power level (L
) : 94.32 dB (A)
WA
Uncertainty (K) : 0.94 dB(A)
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN50636-2-100:2014:
Work mode: operation without load (blowing)
Vibration emission (a
) : < 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
Work mode: operation without load (vacuuming)
Vibration emission (a
) : < 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
) : 81.8 dB (A)
pA
2
2
2
2
Declarations of Conformity
For European countries only
The Declarations of conformity are included in Annex A
to this instruction manual.
SAFETY WARNINGS
Cordless Blower Vacuum Safety Instructions
WARNING:
Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
Training
Read the instructions carefully. Be familiar with
1.
the controls and the correct use of the machine.
2.
Never allow children, persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge or people unfamiliar
with these instructions to use the machine. Local
regulations may restrict the age of the operator.
Never operate the machine while people, espe-
3.
cially children, or pets are nearby.
Keep in mind that the operator or user is respon-
4.
sible for accidents or hazards occurring to other
people or their property by failure to follow the
instructions in this instruction manual.
Preparation
Always wear substantial footwear and long
1.
trousers while operating the machine.
Do not wear loose clothing or jewellery that can be drawn
2.
into the air inlet. Keep long hair away from the air inlets.
3.
Always wear protective goggles to protect your eyes
from injury when using power tools. The goggles
must comply with ANSI Z87.1 in the USA, EN 166 in
Europe, or AS/NZS 1336 in Australia/New Zealand. In
Australia/New Zealand, it is legally required to wear
a face shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
6 ENGLISH
Publicidad
