LEXIBOOK Power Puppy DOG01 Manual De Instrucciones página 3

ENGLISH
PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
Before using the unit, be sure to read all operating instructions carefully. Please note that these are general precautions and
may not pertain to your unit.
1. Read this Instruction Manual before you attempt to connect or operate the appliance.
2. Keep these instructions in good condition. Heed all warnings. Follow all instructions.
3. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product.
Dry location use only.
4. No naked flame source, such as candles, should be placed on the product
5. Ventilation should not be impeded by covering the ventilation openings.
6. Only use accessories, which are specified by the manufacturer
7. Place the unit where there is good ventilation. Place the system on a flat, hard and stable surface. Do not expose to temperatures above
40°C. Allow at least 10 cm clearance from the rear and the top of the unit and 5 cm from each side
8. Batteries should be disposed of properly. Take them to the collection container in order to protect the environment.
9. Keep minimum distances around the apparatus for sufficient ventilation.
10. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.
11. The use of apparatus in moderate climates.
When opening the product's packaging, please ensure that the following elements are included:
1 x POWER PUPPY® robot
WARNING: All packaging materials, such as tape, plastic sheets, wire ties and tags are not part of this toy and should be
discarded for your child's safety.
The robot operates with 1 x DC 3.7V
rechargeable battery
Charging the robot :
1. Check that the unit is switched off.
2. Using a screwdriver, open the battery door located at the rear of the unit.
3. Delicately remove the rechargeable battery from the compartment. Unplug it by pinching both
sides of the connector (see figure 1)
4. Insert the small end of the USB charging cable (included) into the battery connector.
5. Connect the other end of the USB cable into the USB port of your powered computer or USB
type power adaptor and connect it to a wall socket (see figure 2).
6. The LED indicator on the USB cable turns red when charging, and turn off when fully charged.
USB cable specifications:
Input Power: 5.0V
Output Power: 3.7V
The toy is only to be connected to Class II equipment bearing the following symbol
Note: If connect with an adaptor, please only use the adaptor for toys and it should be with this symbol
Note: Please note that the USB cable can be used for battery charging only and not for data transfer.
Warning: Disconnect the adapter if the game is not used for a long period of time to prevent overheating. When the game is powered by
an adapter, do not play outside. Check the state of the adapter and the connection cords regularly. If their condition is deteriorating, do not
use the adapter until it has been repaired. The toy shall only be used with a transformer for toys. The adapter is not a toy. The device should
be disconnected from the power supply to be cleaned if liquids are used for cleaning. The toy is not intended for children under 3 years old.
Misuse of transformer can cause electrical shock.
Parental advisory: transformer and adaptor for toys are not intended to be used as a toy. The usage must be under parental advice.
WARNING:
- Danger of explosion if battery is incorrectly replaced. Please only replace it with the same or equivalent battery.
- The battery should not be exposed to high temperatures, such as sunlight, fire or anything similar.
- Significant electromagnetic interference or electrostatic discharges may cause the device to malfunction or lose data. If the device is not functioning
correctly, switch it off and then on again, unplug the USB cable or remove the batteries and insert them again.
- The normal function of the product may be disturbed by strong electromagnetic interference. If so, simply reset the product to resume normal
operation by following the instruction manual. In case the function could not resume, please use the product in other location.
- The toy is not to be connected to more than the recommended number of transformers or power supplies.
- For the purposes of recharging the battery, only use the detachable supply unit provided with this toy.
REMOTE CONTROL:
Battery installation or replacement
1. Use a screwdriver to loosen the screw on the battery compartment located at the back of the remote
control.
2. Install or replace 2 x AA/LR6 batteries, observing the polarity indicated at the bottom of the battery compartment, and as per
the diagram shown opposite.
3. Close the battery compartment and tighten the screw.
Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the toy before being charged. Rechargeable batteries
are only to be charged under adult supervision. Different types of batteries or new and used batteries are not to be mixed. Only batteries of the same or
equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the toy. The supply terminals are not to be short-circuited. Do not throw batteries into a fire. Remove the
batteries if you are not going to use the toy for a long period of time. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
WARNING: Malfunction or loss of memory may be caused by strong frequency interference or electrostatic discharge. Should any abnormal
function occur, remove the batteries and insert them again.
1. Directional keys
2. Hand stand*
3. Volume
4. Angry*
5. Get down*
6. Stop
7. Yoga
8. Push-up*
9. Animal sounds and guard*
* Please long press (around 3 seconds) to access these functions.
Only use a soft, slightly damp cloth to clean the unit. Do not use detergent. Do not to expose the unit to direct sunlight or any other heat
source. Do not immerse the unit in water. Do not dismantle or drop the unit. Do not try to twist or bend the unit.
This product is covered by our 2-year warranty.
For any claim under the warranty or after-sales service, please contact your distributor and present a valid proof of purchase. Our warranty
covers any manufacturing material and workmanship defect, with the exception of any deterioration arising from the non-observance of the
instruction manual or from any careless action implemented on this item (such as dismantling, exposing to heat and humidity, etc.). It is
recommended to keep the packaging for any further reference. In a bid to keep improving our services, we could implement modifications on
the colours and the details of the product shown on the packaging.
WARNING! Not suitable for children under 3 years. Choking hazard – Small parts.
NOTE: Please keep this instruction manual, it contains important information.
Reference: DOG01
Designed and developed in Europe – Made in China.
United Kingdom & Ireland
For after-sales service, please contact us at savcomfr@lexibook.com
Environmental Protection:
Unwanted electrical appliances can be recycled and should not be discarded along with regular household
waste! Please actively support the conservation of resources and help protect the environment by returning this
appliance to a collection centre (if available).
SAFETY INSTRUCTIONS
PACKAGING CONTENTS
1 x instruction manual
BATTERY REQUIREMENTS
500mAh (included)
2.0A
0.5A
DISCOVER POWER PUPPY®
10. Dances
11. Demo
12. Make a program
13. Songs
14. Numbers
15. Say hello!
16. Sit down*
17. Light effects
18. Affectionate*
ENTRETIEN ET GARANTIE
1 x remote control
The remote control operates with 2 x 1.5 AA/
LR6 batteries (not included).
Lexibook S.A.
6 avenue des Andes
Bâtiment 11
91940 Les Ulis
France
www.lexibook.com – © Lexibook®
1x screwdriver 1 x USB charging cable
.
.
Tactile, he reacts
when you pet his
head and starts to
dance!
ON / OFF
Follow us
@LexibookCom