Publicidad
Idiomas disponibles
Idiomas disponibles
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start-up can cause injury.
Assembling the Pole (Fig. A, E, F)
1. To assemble the pole, line up the upper trimmer pole
and the lower trimmer pole
button
and slide the upper trimming pole into the
15
pole bracket
as shown in Fig. E. Ensure the latching
7
button engages the latch hole
2. Secure the poles by tightening the middle bolt
the supplied hex wrench
Attaching Guard (Fig. G)
WARNING: Never remove the guard. Damage or
personal injury could result.
WARNING: NEVER OPERATE appliance WITHOUT
GUARD FIRMLY IN PLACE. The guard must always be
properly attached on the appliance to protect the user.
1. Assemble the guard
8
2. Using a cross head screwdriver, insert the 6 guard
screws
18
and tighten securely.
Attaching the Auxiliary Handle (Fig. A, H)
1. Place the auxiliary handle
base
19
so the upper trimmer pole
2. Hold the auxiliary handle in place and slide the handle
bolts
into the handle from the top, threading them
20
into the handle base.
3. Tighten the handle bolts with the supplied hex
wrench
21
. Ensure the handle is securely attached.
4. Repeat for the other side of the auxiliary handle.
. Press down the latching
6
.
14
16
17
as shown in Fig. F.
to the motor housing
4
.
3
on top of the handle
5
is between them.
Adjustment (Fig. H, I)
WARNING: To reduce the risk of serious personal
injury, turn appliance off and remove battery
before making any adjustments or removing/
installing attachments or accessories.
WARNING: Never remove the guard. Damage or
personal injury could result.
WARNING: NEVER OPERATE appliance WITHOUT
GUARD FIRMLY IN PLACE. The guard must always be
properly attached on the appliance to protect the user.
The auxiliary handle
However, if adjustment is necessary, loosen the four handle
bolts
with a hex wrench
20
handle up or down the upper trimmer pole
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start-up can cause injury.
CAUTION: Before you begin trimming, only use the
appropriate type of cutting line.
CAUTION: Inspect area to be trimmed and remove
any wire, cord, or string-like objects which could
become entangled in the rotating line or spool. Be
particularly careful to avoid any wire which might be
5
bent outwardly into the path of the appliance, such as
barbs at the base of a chain link fence.
Installing and Removing the Battery Pack
(Fig. J)
with
WARNING: Make certain the lock-off lever is not
engaged to prevent switch actuation before removing
or installing battery.
NoTE: For best results, make sure your battery pack
fully charged.
To install the battery pack: Align the battery pack with
the rails inside the battery housing
housing until the battery pack is firmly seated and ensure
that it does not disengage.
To remove battery pack: Depress the battery pack release
button
12
and firmly pull the battery pack out of the battery
housing. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. K)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the handle
and one hand on the auxiliary handle
is positioned to maximize balance.
3
and slide the auxiliary
21
.
5
and slide it into the
10
3
.
ENglish
11
is
13
29
Publicidad
