Descargar Imprimir esta página

Bosch GTM 12 Professional Manual Original página 56

Ocultar thumbs Ver también para GTM 12 Professional:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 98
OBJ_BUCH-302-007.book Page 56 Tuesday, December 7, 2010 11:10 AM
56 | English
Noise/Vibration Information
Measured sound values determined according
to EN 61029.
Typically the A-weighted noise levels of the
product are: Sound pressure level 99 dB(A);
Sound power level 112 dB(A). Uncertainty
K =3 dB.
Wear hearing protection!
Operation as Chop and Mitre Saw:
Vibration total values (triax vector sum) deter-
mined according to EN 61029:
Vibration emission value a
2
tainty K =1.5 m/s
.
The vibration emission level given in this infor-
mation sheet has been measured in accordance
with a standardised test given in EN 61029 and
may be used to compare one tool with another.
It may be used for a preliminary assessment of
exposure.
The declared vibration emission level repre-
sents the main applications of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may signifi-
cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that
the product described under "Technical Data" is
in conformity with the following standards or
standardization documents: EN 61029,
EN 60825-1 according to the provisions of the
directives 2004/108/EC, 2006/42/EC.
EC Type Certification No. 3400637.01CE by no-
tified testing agency No. 2140.
1 609 929 V07 | (7.12.10)
Technical file at:
Robert Bosch GmbH, Dept. PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 04.02.2010
2
<2.5 m/s
, Uncer-
h
Assembly and Transport
Delivery Scope
Carefully remove all parts provided from their
packaging.
Remove all packing material from the power tool
and the accessories provided.
Before starting the operation of the machine for
the first time, check if all parts listed below have
been supplied:
– Combination saw with pre-mounted saw
– Allen key/slotted screwdriver 5
– Dust bag 8
Additionally for table saw:
– Parallel guide 63
– Push stick 64
– Lower saw blade cover 68
Note: Check the power tool for possible damage.
Before further use of the machine, check that all
protective devices are fully functional. Any light-
ly damaged parts must be carefully checked to
ensure flawless operation of the tool. All parts
must be properly mounted and all conditions
fulfilled that ensure faultless operation.
Damaged protective devices and parts must be
immediately replaced by an authorised service
centre.
Dr. Eckerhard Strötgen
Head of Product
Certification
Avoid unintentional starting of the ma-
chine. During assembly and for all work on
the machine, the power plug must not be
connected to the mains supply.
blade
Bosch Power Tools

Publicidad

loading

Este manual también es adecuado para:

0 601 b15 000