Atlas Copco ETD STR61-90-13 Información Seguridad página 5

ETD STR61-90-13
Atlas Copco Ltd
Swallowdale Lane
Hemel Hempstead
Hertfordshire HP2 7EA
Safety
DO NOT DISCARD - GIVE TO USER
WARNING Read all safety warnings, instructions, il-
lustrations and specifications provided with this prod-
uct.
Failure to follow all instructions listed below may result
in electric shock, fire, property damage and/or serious in-
jury.
Save all warnings and instructions for future refer-
ence.
WARNING All locally legislated safety rules regard-
ing installation, operation and maintenance shall be
respected at all times.
Statement of Use
• For professional use only.
• This product and its accessories must not be modified in
any way.
• Do not use this product if it has been damaged.
• If the product data or hazard warning signs on the product
cease to be legible or become detached, replace without
delay.
• The product must only be installed, operated and serviced
by qualified personnel in an industrial environment.
Intended Use
This product is designed for installing and removing threaded
fasteners in wood, metal or plastic. Indoor use only.
No other use permitted.
Product Specific Instructions
Special precautions for STR and ETT tools
WARNING Risk of injury
Major changes in joint characteristics will affect the op-
erator reaction force and can injure the operator.
Avoid using tightening strategies in applications out-
►
side their limitations.
Recommended value for Rundown Complete is 10%
►
of target torque.
Installation
General Installation Safety
Refer installation to qualified personnel only.
Hang the tool securely, by for example using a balancer.
When using a suspension yoke, check that it is in good condi-
tion and correctly fastened.
© Atlas Copco Industrial Technique AB - 9834 2534 00
Always connect the system to an earthed outlet. Always make
sure that the mains plug is disconnected and the controller is
turned off before connecting or disconnecting the tool cable.
Operation
Dual Trigger
Dual trigger (Recommended to use during
operation)
WARNING Crushing Hazard
The Dual trigger forces the user to use both hands to op-
erate the tool. If not used, the operator can accidentally
start the tool while adjusting the crowfoot, thus resulting
in a serious hand injury.
Make sure the tool cannot be started once the Dual
►
trigger has been released.
Always test the tool by first releasing the trigger of
►
the Dual trigger, then push the trigger of the tool. If
the tool starts; stop working.
General Instructions
The tool may only be used together with the associated torque
reaction bar, which is adapted to the screw joint application
concerned.
WARNING Crushing Hazard
Check the rotational direction of the tool before start! A
start in an unexpected rotational direction can cause bod-
ily injury or property damage. Moving parts can crush
and cut.
Make sure that the rotational direction of the tool is
►
correct before starting the tool.
Keep hands and fingers away from moving parts.
►
General Operation Safety
• Due to entanglement risk, do not wear gloves.
• Be prepared of the reaction force which will occur
when the tool is used. Always support the tool's handle
securely in the direction opposite to the spindle rotation,
in order to reduce the effect of sudden torque reaction
during final tightening and initial loosening.
• Never hold the drive, socket or drive extension.
• Operators and maintenance personnel must be physi-
cally able to handle the bulk, weight and power of the
tool.
• If possible, use a suspension arm to absorb the reac-
tion torque. If that is not possible, side handles are
recommended for straight-case and pistol-grip tools;
reaction bars are recommended for angle nutrunners.
It is recommended to use a means to absorb the reaction
torque above 4 Nm (3 lbf.ft) for straight-case tools, above
10 Nm (7.5 lbf.ft) for pistol-grip tools, and above 60 Nm
(44 lbf.ft) for angle nutrunners.
Safety Information
5