Descargar Imprimir esta página

Bosch RA1171 Instrucciones De Funcionamiento Y Seguridad página 17

Ocultar thumbs Ver también para RA1171:

Publicidad

Idiomas disponibles

Idiomas disponibles

CHART 1
Router
Router
Brand
Model
Bosch
1613 series
Bosch
1617 series (fixed
base models only)
Bosch
MR series
Craftsman
Most Craftsman
1/2" collet routers
DeWalt
DW616, DW618
(fixed base only)
Hitachi
M12VC
Makita
RF1100, RF1101
Milwaukee
5615, 5616
Porter-Cable
690 series,
7529 plunge router,
and 892–895 series
(fixed base only)
Ryobi
R161, R162, R163
Ryobi
RE170, RE180 PL
Skil
1810, 1815, 1820, 1825
*RE170 requires the subbase attached for specified fastener length.
ATTACH ROUTER TO MOUNTING PLATE
(Figs. 11 and 12)
Disconnect the router from the
power supply before installing
router into the table, making adjustments, changing
accessories, removing the router from the table,
performing maintenance, or storing the tool. Such
precautionary safety measures reduce the risk of
unintentional tool operation.
1. Remove the plastic subbase from your router
(unless otherwise specified in Chart 1) (Fig. 11).
If you wish to mount the router with the subbase,
you may need to purchase longer fasteners. Using
the subbase affects the range of cutting depth.
2. If your router has its own dust extraction hood that
mounts to the top of the metal router base and you
want to use it under the router table, this is a
convenient time to install it.
3. Using Chart 1, determine the hardware and mount
type for your router.
For most router models, the screws are driven into
threaded holes in the routerʼs base (mount type 1).
For some router models, the screws go all the way
through the base and are fastened with washers
and nuts (mount type 2).
Competitor routers are outside of BOSCHʼs control.
Changes made to these routers may affect the
compatibility to the fasteners specified and/or
supplied with this table.
Always make sure the screw is fully seated on
the adapter plate and that the router base is
firmly against the adapter plate to ensure secure
mounting. If the router, plate, and fasteners do not
seat together properly, you may need to purchase
new fasteners of a different length or size.
Router Table Assembly
Hole
Fasteners
Pattern
Required
" Pan-head Phillips machine screws (46),
A
1/4-20 x 1
1
2
washers (31), and 1/4-20 nuts (49)
B
#10-24 x 1/2" Pan-head Phillips machine screws (47)
B
M4 x 20 Pan-head Phillips machine screws (51)
E
5/16-18 x 1/2" Pan-head Phillips machine screws (50)
B
#8-32 x 1/2" Pan-head Phillips machine screws (48)
B
#10-32 x 1/2" Pan-head Phillips machine screws (45)
B
#10-24 x 1/2" Pan-head Phillips machine screws (47)
B
#10-24 x 1/2" Pan-head Phillips machine screws (47)
B
#10-24 x 1/2" Pan-head Phillips machine screws (47)
E
5/16-18 x 1/2" Pan-head Phillips machine screws (50)
F
5/16-18 x 1/2" Pan-head Phillips machine screws (50)*
D
#10-32 x 1/2" Pan-head Phillips machine screws (45)
to the router table base. While working, periodically
check the router base fastenersʼ clamping tightness.
Router motor vibration can loosen fasteners during use,
causing the router to fall from the table.
4. Refer to the mounting plate guide (Fig. 10) on page 15
and align the appropriate mounting plate holes for your
router to the router base holes. Make sure that the
depth adjustment controls on the router face the front
of the mounting plate. Figure 10 shows the proper
orientation of the plate when installed on the table.
5. Securely mount your router to the mounting plate
(Fig. 12).
FIG. 12
16
Before using the router table, verify
that the router is securely clamped
FIG. 11
REMOVE
SUBBASE
Mount
Type
2
1
1
1
1
1
1
1
1
1
1
1

Publicidad

loading

Este manual también es adecuado para:

Ra1165