Levenhuk Ermenrich Zing TC33 Guia Del Usuario página 5

Non-contact voltage detection (NCV)
Press the FUNC button (3) to select the NCV/Live function. NCV is displayed. Slowly bring the NCV probe close to the point to be detected.
When the signal of a weak electromagnetic field is detected, the "– – – L" will appear on the screen, the built-in buzzer will produce a slow
beep sound, and the LED indicator will glow green. When the signal of a strong electromagnetic field is detected, the "– – – H" will appear on
the screen, the built-in buzzer will produce a quick beep sound, and the LED indicator will glow red.
When using this function, remove the test leads from the jacks.
Live detection
Press the FUNC button (3) to select the NCV/Live function. Press the SEL button (2) to display the LIVE symbol. Plug only the red test lead
into the INPUT jack (9). Connect the red test probe to the conductor to be measured. When the signal of a weak electromagnetic field is
detected, the "– – – L" will appear on the screen, the built-in buzzer will produce a slow beep sound, and the LED indicator will glow green.
When the signal of a strong electromagnetic field is detected, the "– – – H" will appear on the screen, the built-in buzzer will produce a quick
beep sound, and the LED indicator will glow red.
Fuse replacement
• Turn off the multimeter power and remove the probes.
• Remove the screws fixing the back cover and remove the back cover.
• Remove the burnt out fuse, replace it with a new one of the same specification, and ensure that the fuse is installed in the safety clip
and clamped tightly.
• Install the back cover and fix it with screws.
Specifications
DC voltage, range
AC voltage, range
DC current, range 1
DC current, range 2
AC current, range 1
AC current, range 2
Resistance, range 1
Resistance, range 2
Capacitance, range 1
Capacitance, range 2
Frequency, range
Duty, range
Counts
Auto-off
Temperature measurement range
Accuracy
Operating temperature range
Operating humidity
Storage temperature range
Storage humidity
Power supply
Safety rating
The manufacturer reserves the right to make changes to the product range and specifications without prior notice.
Care and maintenance
Use the device only within the permitted range. Failure to follow these instructions may result in electric shock, fire and/or personal injury.
When measuring voltage, do not exceed the operating conditions (see "Specifications"). When changing functions and ranges, always
remove the test probes from the test points. Do not use the device if it is not working properly. Please note that the parameters of the power
supply must comply with the technical characteristics of the device. Do not try to disassemble the device on your own for any reason. For
repairs and cleaning of any kind, please contact your local specialized service center. Protect the device from sudden impact and excessive
mechanical force. Do not use the device in aggressive atmosphere. Store the device in a dry cool place. Only use accessories and spare parts
for this device that comply with the technical specifications. Never attempt to operate a damaged device or a device with damaged electrical
parts! If a part of the device or battery is swallowed, seek medical attention immediately.
Battery safety instructions
The device is equipped with a built-in rechargeable lithium-ion battery. This avoids frequent battery replacement. Always switch the device
off when not in use. If the battery charge is low, please recharge the device in time to ensure that the measurements are accurate. Do not
overheat the battery. Do not discharge the battery completely. Only use the original charger.
600mV / 6V / 60V / 600V ±(0.5%+3)
600mV / 6V / 60V / 600V ±(0.8%+3)
600mA / 6A ±(1.2%+3)
10A ±(1.8%+3)
600mA / 6A ±(1.2%+3)
10A ±(1.8%+3)
600Ω / 6kΩ / 60kΩ / 600kΩ / 6MΩ ±(1.0%+5)
60MΩ ±(1.5%+10)
6nF / 60nF / 600nF / 6μF / 60μF / 600μF ±(4.0%+5)
6mF / 60mF ±(5.0%+5)
60Hz / 600Hz / 6kHz / 60kHz / 600kHz / 6MHz / 10MHz ±(1.0%+3)
1–99% ±(3.0%+3)
6000
15min.
–40... +1000°C / –4... +1832°F ±(1.0%+3)
–40... 0°C / –40... +32°F: ±3°C / 6°F
0... +1000°C / +32... 1832°F: ±2%
0... +40°C / +32... 104°F
0–80% RH
–10... +60°C / +14... 140°F
0–70% RH
3.7V, 1400mA·h rechargeable lithium battery
EN61010-1,-2-030; EN61010-2-033; EN61326-1; Cat. III, 600V
5