General Power Tool Safety Warnings; Belt Sander Safety Warnings; Functional Description - Makita 9032 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Lock lever
2 Arm
3 "A" range
4 Screw
5 Lock button
6 Switch trigger
7 Speed adjusting dial
SPECIFICATIONS
Model
Belt size ................................................. 9 mm x 533 mm
Belt speed ...................................................... 5 – 28 m/s
Overall length ..................................................... 420 mm
Net weight ............................................................. 1.6 kg
Safety class ............................................................... /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.

General Power Tool Safety Warnings

WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

BELT SANDER SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces,
because the belt may contact its own cord. Cut-
ting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
2. Ventilate your work area adequately when you
perform sanding operations.
3. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
4. Always use the correct dust mask/respirator for
the material and application you are working
with.
5. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
6. Hold the tool firmly with both hands.
4
Explanation of general view
8 Abrasive belt
9 Cam lever
10 Rear pulley
11 Adjusting dial
12 Dust nozzle
13 Hose 28
14 Hose for vacuum cleaner
7.
9032
8.
9.
10. This tool has not been waterproofed, so do not
SAVE THESE INSTRUCTIONS.
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
ENE052-1
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

• Always be sure that the tool is switched off and
ENF002-2
unplugged before adjusting or checking function on the
tool.
Adjusting arm inclination (Fig. 1)
The arm can be pivoted and fixed at any desired angle
within the "A" range according to the operating position or
the figure of the workpiece.
GEA010-1
Loosen the lock lever by raising it. Pivot the arm to the
desired position, and secure the lock lever to fix the arm
firmly.
Replacing arm (Fig. 2)
By replacing the standard-equipped arm by optional one,
6 mm or 13 mm width belt can be used. Remove the arm
by loosening the screw that secures the arm. Insert the
arm that fits the belt to be used, and tighten the screw
firmly.
GEB015-3
Switch action (Fig. 3)
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, and then release it.
15 Vacuum cleaner
16 Dust collector
17 Flat shoe
18 Limit mark
19 Brush holder cap
20 Screwdriver
Make sure the belt is not contacting the work-
piece before the switch is turned on.
Keep hands away from rotating parts.
Do not leave the tool running. Operate the tool
only when hand-held.
use water on the workpiece surface.
WARNING:
CAUTION:
CAUTION: