SOLAC CVG9611 Instrucciones De Uso página 10

you would hear a strange noise from the mi-
cro-pump. Switch off the steam selector to pre-
vent any damage to the system.
Switch off the appliance and fill the water tank.
•
When switching it on again, this noise will dis-
appear.
USE:
Unroll the cable completely before plugging it
•
in.
Connect the appliance to the mains.
•
Temperature and steam status are shown
•
on the screen (G), when both values remain
steady this indicates that the CVG is ready for
use, it will also beep when it reaches its setting.
To select the various programs just turn the
•
digital screen to the left or right depending on
whether we wish to increase or decrease the
program number, the program will change with
a slight turn. Left decreases, right increases.
(Fig. 2) once turned, the dial will return to po-
sition.
Given that the soleplate takes a long time to
•
cool, we recommend starting off with delicate
garments and then increasing the program
setting.
PROGRAM GARMENTS
0 Off
1 Antisheen, special setting to avoid creating
sheen on dark garments
2 ECO setting, the most efficient, optimised for
cost-effective ironing.
3 Delicates; ironing directly on T-shirts with printed
decals and any delicate garment.
4 AUTO; single setting suitable for all type of
ironing, except for very delicate garments.
5 Ironing shirts and cotton garments
6 Denim jeans and heavy cotton
7 Linen; fabrics that are difficult to iron.
8 TURBO; Maximum temperature and steam flow
for ULTRA FAST ironing.
-IMPORTANT: If the fabric is made up of var-
•
ious kinds of fibres, select the temperature for
the fibre that requires the lowest temperature.
(For example, select the temperature for pol-
yester for a fabric made out of 60% polyester
and 40% cotton (pos. 3)).
- Temperature and steam status are shown on
•
the
PRESENCE SENSOR (D)
The CVG is equipped with a presence sensor
•
(D) that instantly shuts off the steam outlet if
the handle is not being held. This leads to en-
ergy savings and increased autonomy of the
water tank (lower water consumption).
Steam flow is automatically re-established by
•
holding the handle on the CVG
Removing your hand from the handle does not
•
switch off the selected steam function, it only
interrupts the steam flow temporarily until it de-
tects that the handle is being gripped again.
The screen continues to display the icon for
the selected steam function.
DRY AND/OR STEAM IRONING
The appliance has a steam control button
•
(C) which, when set to off, allows dry ironing
(without steam) or with steam if it is switched
on, a light indicates its status, on/enabled off/
disabled.
EXTRA STEAM:
It is possible to iron with maximum steam flow
•
regardless of the setting. To do this, in the case
of steam ironing, just press the steam button
(c), the steam flow will increase to maximum,
to stop steam production just press the steam
button again. The screen displays the current
setting, with a steam bar which shows empty
when switched off, up through the various set-
tings for each program to maximum when the
super steam setting is activated.
STEAM BLAST:
This function provides extra steam for remov-
•
ing creases.
Press the steam blast button (B) only in pro-
•
grams 7 and 8, the screen will display an icon
to indicate when the EXTRA function (Fig
2) is ready. With the lower programs, sole-
plate temperature is not sufficient to produce
a steam blast, consequently the super steam
icon will not be displayed. Wait a few seconds
until the steam penetrates the fibres of the
garment before pushing the button again. For
optimum steam quality, do not apply more than
three successive blasts.
During initial use it is necessary to press re-
•
peatedly in order to prime the super steam
water circuit.
VERTICAL IRONING:
It is possible to iron hanging curtains, items of
•
clothing on their own hanger, etc. To do so, fol-
low these instructions:
Iron from top to bottom while pressing the
•
steam control (B), follow the instructions given
EN