Technical Specifications; Maintenance And Storage; Safety Instructions - Hudora 11116 Instrucciones De Montaje Y De Uso

INSTRUCTIONS ON aSSEMBLY aND USE
EN
CONGRaTULaTIONS ON PURCHaSING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral com-
ponent of the product. Therefore, please store them and the packaging carefully
in case questions arise in the future. Please always include these instructions
when handing on the product to a third party. This product must be assembled
by an adult. This product is not designed for industrial use. The use of the pro-
duct requires certain capabilities and skills. Always adjust according to the age
of the user and use for the purpose it has been designed for.

TECHNICaL SPECIfICaTIONS

Item: Skater Ramp Set
Item number: 11118 (5-parts) | 11116 (3-parts)
Item weight: 11118: about 6.4 kg | 11116: about 3 kg
Max. load capacity: 11118: about 80 kg | 11116: about 60 kg
If you have assembly problems or would like further information on the product,
we have all you need and more at http://www.hudora.de/.
CONTENTS
11118 11116
4x Ramp 2x Ramp
1x Connecting piece 1x Connecting piece
1x Manual 1x Manual
Other items included are meant to facilitate safe transportation and are not re-
quired for the installation and use of the product.

SafETY INSTRUCTIONS

• This product is designed for riders with sufficient experience.
• The product may be used by children only under adult supervision.
• This product is intended exclusively for use with suitable roller sports equip-
ment.
• This product is designed for a certain weight and a specific use. Please ob-
serve the permissible maximum load capacity in the „Technical Specifica-
tions".
• Attention! Biking, skating and other similar sports can be dangerous and lead
to injuries. This is especially applicable when these activities are performed
on ramps, rails or other obstructions that may increase the risk of injury.
Regardless of your performance level, you should always use protective
clothing, such as hand and wrist guards, knee and elbow pads as well as a
helmet. Learn the crossing of the ramps with care and properly.
• Make sure before each use that all the fittings fit properly, all parts securely
connected to each other and all screws are tight.
• The product and all other products that are used together with it must be
used on a non-slip, level surface that is free of stones, gravel and other rub-
ble. Always also read and follow the Instructions and safety notes accompa-
nying the other products that you can use in combination with the ramp set.
• You should never use the ramp set near cars or pedestrians. The ramp set
should always be placed on an available free area in a traffic free zone. The
product and all other products that are used together with it may never used
on feeder roads with traffic, on hills, near water, retaining walls and railings
as well as other obstacles and potential risk sources.
• The ramp set should never be used in wet, cold or freezing weather.
• The use of the rump set is performed at your own risk. With the use of the
ramp set and related products, the user acknowledges the possible hazards
and risks and bears the responsibility for his usage behaviour. Failure to com-
ply with the listed safety instructions as well as and unreasonable behaviour
can lead to further risks and injuries.
• The ramp set should never be used if the connector piece is not securely
fixed.
• Never use only one ramp and a connector piece.
All images are examples of the design.
INSTRUCTIONS ON aSSEMBLY
• Remove the connector piece and remove the wing nuts that are attached to
it. Put them aside so that you can use them later in the course of the assem-
bly.
• Attach a ramp to it.
• Insert the connector piece on the upper side of the ramp. Slide the screws
through the holes provided, so that they can be seen on the opposite end.
The connector must rest firmly on the ramp.
• Carefully the tightly screw the ramp to the connecting piece on the side with
the wing nuts.
• Repeat the above steps with the other provided ramp.
• To disassemble the connected ramps, please perform the above described
assembly steps in the reverse order.

MaINTENaNCE aND STORaGE

Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and
after each use. Do not make any structural changes. For your own safety, please
use original spare parts only. These can be sourced from HUDORA. If parts
become damaged or if sharp edges or corners should develop, the product may
not be used any more. If in any doubt, please contact our service team (http://
www.hudora.de/). Store the product in a safe place where it is protected from
the elements, cannot be damaged, and cannot injure anyone.
DISPOSaL aDvICE
At the end of the product's life, please dispose of it at an appropriate collection
point provided in your area. Local waste management companies will be able to
answer your questions on this.
SERvICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. Therefore, you can find numerous
information on the product, replacement parts, solutions to problems and lost
assembly manuals at http://www.hudora.de/service.
4/8