Makita 3706 Manual De Instrucciones página 5

Ocultar thumbs Ver también para 3706:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
ENGLISH
(Original instructions)
1
Shoe
2
Thumb screw
3
Switch lever
4
Bump off switch
5
Bit
6
Collet nut
7
Shaft lock
SPECIFICATIONS
Model
Collet chuck capacity.......................... 3.18 mm, 6.35 mm
–1
No load speed (min
) ........................................... 32,000
Overall length ...................................................... 250 mm
Net weight............................................................... 1.1 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting gypsum, wood, plastic and
soft wall tiles.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future refer-
ence.
CUTOUT TOOL SAFETY WARNINGS
1.
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
3.
Wear eye protection and dust mask.
4.
Ventilate your work area adequately.
5.
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
6.
Check for the proper clearance beneath the
workpiece before cutting so that the bit will not
strike a hard surface such as the floor, work-
bench, etc.
Explanation of general view
8
Adapter
9
Wrench
10 Loosen
11 Tighten
12 Collet cone
13 Circular guide
14 Projections
7.
3706
8.
/II
9.
10. Make sure that the shaft lock is released before
ENE012-1
11. Always use with the shoe securely attached to
12. Hold the tool firmly.
ENF002-2
13. Do not perform any operation using your hands
14. Keep hands away from moving parts.
15. Do not use this tool for drilling.
16. Do not leave the tool running. Operate the tool
GEA010-1
17. Always switch off and wait for the bit to come to
18. Do not touch the bit or the workpiece immedi-
19. Always lead the power supply cord away from
20. Draw attention to the need to use cutters of the
GEB083-1
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
15 Knob
16 Vacuum cover
17 Hose 28
18 Hose for vacuum cleaner
19 Dust collector
Do not cut metal objects such as nails and
screws. Inspect for and remove all nails, screws
and other foreign material from the workpiece
before operation.
Check that the bit is not contacting the work-
piece before the switch is turned on. Always
hold the tool with two hands while switching the
tool on. The motor torque can cause the tool to
turn.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
the switch is turned on.
the tool and positioned flat and firmly against
the workpiece.
to support or guide the workpiece.
only when hand-held.
a complete stop before removing the bit from
workpiece.
ately after operation; it may be extremely hot and
could burn your skin.
the tool towards the rear.
correct shank diameter and which are suitable
for the speed of the tool.
5

Publicidad

Tabla de contenido
loading

Tabla de contenido