Fender Bassbreaker 15 Manual De Instrucciones página 3

Using two speaker enclosures of different impedance ratings is not rec-
ommended. If using enclosures with different ratings, set IMPEDANCE
 SELECT switch (M) to the lower of the two speaker enclosure ratings.
When using both speaker jacks, do not use an enclosure rated at less
than 4Ω. When using MAIN SPEAKER jack alone, do not use an enclo-
sure rated at more than 16Ω.
N. PARALLEL SPEAKER OUTPUTS: Connect external speaker enclosures
here. To avoid damage, turn the amplifier off when changing speaker
connections. For the Bassbreaker 15 combo, use an external speaker
enclosure in combination with the internal speaker by plugging external
enclosure into EXTENSION SPEAKER. To use an external speaker enclo-
sure only, plug external enclosure into MAIN SPEAKER (internal speaker
will automatically be disconnected). For the Bassbreaker 15 amp head,
use the MAIN SPEAKER jack when using only one enclosure (there will
be no sound if the MAIN SPEAKER jack is not used). See tables below for
acceptable parallel speaker enclosure impedance combinations for the
Bassbreaker combo (first table) and amp head (second table) models.
Bassbreaker 15 combo acceptable parallel speaker enclosure imped-
ance combinations with correct IMPEDANCE SELECT switch (M) set-
tings:
INTERNAL SPEAKER MAIN SPEAKER EXTENSION SPEAKER
8Ω NONE
8Ω NONE
DISCONNECTED* 16Ω
DISCONNECTED* 8Ω
DISCONNECTED* 4Ω
DISCONNECTED* 16Ω
DISCONNECTED* 8Ω
*NOTE: When a plug is inserted into MAIN SPEAKER jack, internal speaker load (8Ω) is
automatically disconnected and does not affect total impedance load.
TYPE
POWER
IMPEDANCE
SPEAKER (COMBO)
EXTERNAL SPEAKER ENCLOSURE
TUBES
ACCESSORIES
DIMENSIONS (COMBO)
DIMENSIONS (HEAD)
WEIGHT (COMBO)
WEIGHT (HEAD)
IMPEDANCE SELECT
NONE 8Ω
8Ω 4Ω
NONE 16Ω
NONE 8Ω
NONE 4Ω
16Ω 8Ω
8Ω 4Ω
Specifications
PR 3034
Requirements: 95 watts
1MΩ
12" Celestion® V70 S6125 (8Ω, PN 7700343000)
Bassbreaker BB-112 (optional, PN 226700000), Bassbreaker BB-212 (optional, PN 226800000)
V1-V3: 7025/12AX7A/ECC83
Combo cover (optional, PN 7707953000)
Width: 19.56" (49.68 cm)
Width: 19.56" (49.68 cm)
40 lbs. (18.16 kg)
25.5 lbs. (11.57 kg)
Product specifications subject to change without notice.
Bassbreaker 15 amp head acceptable parallel speaker enclosure
impedance combinations with correct IMPEDANCE SELECT switch (M)
settings:
MAIN SPEAKER EXTENSION SPEAKER
16Ω
8Ω
4Ω
16Ω
8Ω
O. EFFECTS LOOP: Optimized for use with pedals. Connect SEND to
effects input and RETURN to effects output.
P. CABINET EMULATION: Pushbutton switch sends a speaker-emulated
signal through the DIRECT OUT (R) to recording and sound reinforcement
equipment (instead of preamp-only signal).
Q. GROUND LIFT: Pushbutton switch helps eliminate unwanted
electrical noise associated with ground loops.
R. DIRECT OUT: High-quality XLR output sends preamp signal for
recording and sound reinforcement use.
For questions and troubleshooting, contact a Fender
specialist at:
1-800-856-9801 (U.S. toll free)
1-480-596-7195 (International)
Output: 15 watts into 16Ω/8Ω/4Ω
V4-V5: EL84
Amp head cover (optional, PN 7707954000)
Height: 17.5" (44.45 cm)
Height: 9.75" (24.76 cm)
IMPEDANCE SELECT
NONE 16Ω
NONE 8Ω
NONE 4Ω
16Ω 8Ω
8Ω 4Ω
Depth: 9" (22.86 cm)
Depth: 8.81" (22.37 cm)
3