Hunter 99363 Manual De Instrucciones

Model 99363
Weight (± 2lbs): 2.9 (1.3 kg)
ONE YEAR WARRANTY
This product is warranted to the original purchaser by Casablanca Fan Company/Hunter
Fan Company against defects in material and workmanship for one (1) year from date of
purchase. During the warranty period, we will repair or, at our option, replace a defective
product at no charge. For information on how to obtain service, contact the Casablanca/
Hunter Service Department by calling our toll-free number at 888-830-1326. Damage to
the product caused by mishandling, improper installation or modification is not covered
by this warranty. This warranty is given in lieu of all other warranties expressed or implied.
Some states do not allow limitations of time on an implied warranty, therefore the above
limitations may not apply in every case. This warranty states specific legal rights which
may vary from state to state.
Read and Save These Instructions
This product conforms to UL Standard 507
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation
is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the
device.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one
or more of the following measures: Reorient or relocate the receiving
antenna, Increase the separation between the equipment and
receiver, Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. Consult the dealer or
an experienced radio/TV technician for help. Note: Any changes or
modifications to the transmitter or receiver not expressly approved by
Hunter Fan Company may void one's authority to operate this remote
control.
If you have problems installing or operating your light kit, do not return this
product to the dealer. Call our Consumer Affairs Hotline.
Installation
1
Turning off the power
Ensure the power is OFF at the outlet box and
wall switch location before proceeding with
installation.
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
WARNINGS
888-830-1326
2
Removing bottom cap
Remove the two screws
securing the bottom cap to
the bottom of the fan.
3
Wiring the Light Kit
Using the single pin
connectors, connect the
black or blue wire from the
fan to the black wire from
the light kit. Connect the
white wire from the fan to
the white wire from the light
kit. Push the excess wiring
into the ligh tkit.
4
Installing the Light Kit
Using the two screws from
the light kit hardware bag,
install the screws through
the two screw holes in the
light and into the fan.
5
Installing the Glass
Align the notches in the
outer rim of the globe
with the tabs on the light
kit assembly Carefully lift
the globe up inside the
light fixture as far as it will
go. Rotate the globe in a
clockwise direction until it is
held tightly in place by the
three tabs.
Troubleshooting
• Make sure the power switch is on.
• Check the circuit breaker to ensure the power is turned on.
OFF
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan's wiring instructions.
Verify that the wiring is connected correctly.
MA054 • 01/09/17 • © 2017 Hunter Fan Company