koban KPF-02 Instrucciones De Uso página 22

OPERATING INST O
AC Vo oltage bandwid dth 50/400H
Opera ating Tempera ture 14 to 12
Storag ge Temperatu re -14 to 1
Relativ ve Humidity 90%(0
45%(4
Altitud de Operat
Over v voltage Catego
Batter ry Two 1.5
Auto O OFF
Dimen nsions/Weight t
Safety y
Operat tion
NOTIC ES: Read and understand all
statement s listed in the s
manual pr rior to using this
switch to t the OFF positio
AC Cu urrent Measur ements
WARN NING: Ensure t that the test lea
discon nnected from th he meter before
clamp measurements s.
1. Set t the Function sw witch to the 400
4A range. If the ra ange of the me
sele ect the higher r range first then
rang ge if necessary y.
2. Pres ss the trigger to o open jaw. Ful
www.gru upotemper.com
KPF-02
TRUCTIONAC CLA AMP METER
Hz (VAC)
o o
22 F (-10 to 50 0 C)
o o
140 F (-30 to 6 60 C)
o o o o
C to 30 C); 75 5%(30 C to 40
o o
40 C to 50 C)
ing: 3000m; St torage 10,000m
ory III 600V
5V "AAA" Batte eries
approx x. 30 minutes
200x5 50x35mm/200g g
For in door use and i n accordance w
Overv voltage Catego ory II, Pollution
Degre ee 2. Category y II includes loc
level, , appliance, po rtable equipme
etc., w with transient o overvoltages le
than Overvoltage C Cat. III
l warning and precaution
safety section o of this operatio
s meter. Set th he function sele
on when the me eter is not in us
ads are
e making curre nt
0 or40A or
asured is not k known,
move to the lo ower
lly enclose one e conductor
KPF-02
OPERATING G INSTRUCTIONA
to o be measured
The clamp meter L LCD will display
read ding.
o o
C);
m
with
DC/A AC Voltage Me easurements
1. Ins sert the black t test lead into th
cal
re ed test lead into o the positive V
ent,
ess
2. Se et the function s switch to the V
3. Se elect AC or DC
4. Co onnect the test
5. Re ead the voltage e measuremen
µA D DC/AC CURRE
1. Ins sert the black t test lead into th
n
re ed test lead into o the positive µ
ect
se.
2.Se et the function s switch to the µA
3. Se elect AC or DC C with the MOD
4. Re emove power f from the circuit
at the point wher re you wish to m
5. To ouch the black
To ouch the red te
6. Ap pply power to t the circuit.
7. Re ead the curren
Resi istance and C Continuity Mea
7 8
AC CLAMP METER R
.
y the
Yes
he negative CO OM terminal and
V terminal.
V position.
with the MOD E button.
leads in parall el to the circuit t under test.
t on the LCD d display.
ENT MEASUR REMENTS
he negative CO OM terminal an
µA terminal.
A position.
DE button.
t under test, the en open up the
measure curre nt.
test probe tip t to the negative e side of the cir
st probe tip to the positive sid de of the circuit
t in the display y.
asurements
d the
d the
e circuit
rcuit.
t.
www.grupotem mper.com