Fuel Safety; Transport And Storage; Fuel; Fuel Handling - Husqvarna 533RS Manual De Instrucciones

Ocultar thumbs Ver también para 533RS:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

H1158941-30,533-553RS,WestII.fm Page 16 Tuesday, July 4, 2017 8:19 AM

Fuel safety

Never start the machine:
1
If you have spilled fuel on it. Wipe off the spillage and
allow remaining fuel to evaporate.
2
If you have spilled fuel on yourself or your clothes,
change your clothes. Wash any part of your body that
has come in contact with fuel. Use soap and water.
3
If the machine is leaking fuel. Check regularly for
leaks from the fuel cap and fuel lines.

Transport and storage

Store and transport the machine and fuel so that there
is no risk of any leakage or fumes coming into contact
with sparks or open flames, for example, from
electrical machinery, electric motors, electrical relays/
switches or boilers.
When storing and transporting fuel always use
approved containers intended for this purpose.
When storing the machine for long periods the fuel
tank must be emptied. Contact your local petrol
station to find out where to dispose of excess fuel.
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
The transport guard must always be fitted to the
cutting attachment when the machine is being
transported or in storage.
Secure the machine during transport.
In order to prevent unintentional starting of the engine,
the spark plug cap must always be removed during
long-term storage, if the machine is not under close
supervision and when performing all service
measures.
WARNING! Take care when handling fuel.
!
Bear in mind the risk of fire, explosion
and inhaling fumes.

Fuel

CAUTION! The machine is equipped with a two-stroke
engine and must always be run using a mixture of petrol
and two-stroke oil. It is important to accurately measure
the amount of oil to be mixed to ensure that the correct
mixture is obtained. When mixing small amounts of fuel,
even small inaccuracies can drastically affect the ratio of
the mixture.
WARNING! Fuel and fuel fumes are
!
highly flammable and can cause serious
injury when inhaled or allowed to come
in contact with the skin. For this reason
observe caution when handling fuel and
make sure there is adequate ventilation.
16 – English

FUEL HANDLING

Petrol
CAUTION! Always use a quality petrol/oil mixture at least
90 octane (RON). If your machine is equipped with a
catalytic converter (see chapter on Technical data) always
use a good quality unleaded petrol/oil mixture. Leaded
petrol will destroy the catalytic converter.
Use low-emission petrol, also known as alkylate petrol, if
it is available.
The lowest octane recommended is 90 (RON). If you
run the engine on a lower octane grade than 90 so-
called knocking can occur. This gives rise to a high
engine temperature, which can result in serious
engine damage.
When working at continuous high revs a higher octane
rating is recommended.

Two-stroke oil

For best results and performance use HUSQVARNA
two-stroke oil, which is specially formulated for our
two-stroke engines. Mixture 1:50 (2%).
If HUSQVARNA two-stroke oil is not available, you
may use another two-stroke oil of good quality that is
intended for air cooled engines. Contact your dealer
when selecting an oil.
Never use two-stroke oil intended for water-cooled
outboard engines, sometimes referred to as outboard
oil.
Never use oil intended for four-stroke engines.
A poor oil quality and/or too high oil/fuel ratio may
jeopardise function and decrease the life time of
catalytic converters.
Petrol, litre
5
10
15
20
Two-stroke oil,
litre
2% (1:50)
0,10
0,20
0,30
0,40

Hide quick links:

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

543rs553rs

Tabla de contenido