Milwaukee 2721-20 Manual Del Operador página 4

Sierra recíproca m18 fuel one-key sawzall
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Selecting a Blade
The Quik-Lok
Blade Clamp can be used with all 1/2"
®
shank universal Sawzall
Sawzall
blades for best performance. When select-
®
ing a blade, choose the right type and length. Many
types of blades are available for a variety of appli-
cations: cutting metal, wood, nail-embedded wood,
scroll cutting, roughing-in, and contours.
Many lengths are also available. Choose a length
long enough to extend beyond the shoe and your
work throughout the stroke. Do not use blades less
than 3-1/2" long since they won't extend beyond
the shoe throughout the stroke.
Installing and Removing Blades from the
Quik-Lok
Remove battery pack before changing blades. Make
sure the spindle and blade clamp areas are clean.
Metal chips and sawdust may prevent the Quik-Lok
Blade Clamp from clamping securely.
1. Depending on the
job, the blade
may be inserted
with the teeth fac-
ing up or down.
To i n s t a l l a
blade, slide the
release lever up.
Insert the blade into the clamp until the tang butts
against the collar.
2. Release the lever and the spring loaded mecha-
nism will clamp the blade firmly in place.
3. Tug on blade to make sure it is securely locked in place.
4. To remove a blade, slide the release lever up
and pull the blade from the tool. Be careful when
handling hot blades.
Quik-Lok
Blade Clamp Maintenance
®
•Periodically clean dust and debris from the
Quik-Lok
Blade Clamp with dry compressed air.
®
• If the collar resists, slide the release lever back and
forth to shake debris loose.
• Periodically lubricate Quik-Lok
a dry lubricant such as graphite.
blades. Use MILWAUKEE
®
Blade Clamp
®
2
Blade Clamp with
®
Removing broken blades from the
Quik-Lok
Broken blades can be removed by the following
methods.
• Remove battery pack before removing blades.
• Point the tool downward, slide up and hold the
release lever, and shake the tool up and down
(DO NOT turn the tool on while your fingers are
holding the blade clamp open). The shank of the
broken blade should drop out of the clamp.
• If shaking the tool doesn't work...
In most cases, a corner of the broken blade will
extend beyond the blade clamp. Slide up and hold
the release lever, and pull the broken blade out of
the clamp by this corner.
• If the broken stub doesn't extend far enough to be
grabbed by its corner, use a thin blade with small
teeth (such as a metal cutting blade) to hook the
blade that is jammed in the clamp while holding up
the release lever, and pull it out.
To reduce the risk of injury, be sure
WARNING
the blade always extends beyond
the shoe and workpiece throughout the stroke.
Blades may shatter if they impact the workpiece
or shoe.
Stroke
®
Stroke
1
4
Blade Clamp
®

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2721-222721-22hdM18 fuel sawzall

Tabla de contenido