D.A.S. CSA Serie Manual Del Usuario página 18

APPENDIX A. Bridge Mode Operation
To operate in bridge mode, follow these steps:
1. Switch off the amplifier.
2. Turn volume control potentiometers on the front panel to minimum position (fully counter-clockwise).
3. Connect input signal to channel A.
4. Set mode switch to "BRIDGE".
5. Connect speakers as follows:
If the selected output voltage is 100 V, the two speaker cables must be connected to the 100 V terminal outputs.
6. A jumper must be connected between 0 volt terminals.
7. Turn volume control potentiometers on the front panel to maximum position (fully clockwise).
8. Control volume levels from the mixer or pre-amp only.
NOTE 1: Always use Class II cables.
NOTE 2: Do not connect low impedance loads to a 70 V/100 V line amplifier.
The following are several examples of bridge mode operation with distributed lines:
The first one is an example for a CSA-300T amplifier, which delivers 300 W in bridge mode at 100 V. The load is 10 x Factor 8T, and
the power selectors are at 100 V/30 W.
A jumper must be connected
between 0 volt terminals.
SPEAKER
OUTPUT
CHANNEL A
0
70V
BRIDGE
70
1 00V
25V
100
1 40V 200V
100
25V
70
1 00V
70V
0
CHANNEL B
In the second example a CSA-600T amplifier is used, which delivers 600 W in bridge mode at 70 V. The load is 10 x Factor 8T, and the
power selectors are at 70 V/60 W.
WATTS
Serie CSA / CSA series
WATTS
50 V 50 V
70 V 70 V
100 V 100 V
Entrada de señal / Signal Input CH A
1 2 2
50 V 50 V
70 V 70 V
100 V 100 V CSA-600T
CAUTION ATTENTION
RISK OF ELECTRIC SHOCK DANGER D'ELECTROCUTION
DO NOT OPEN NE PAS OUVRIR
CH A INPUT
,
BRIDGE OR
PARALLEL
Entrada de señal / Signal Input CH A
STEREO
CH A
PARALLEL BRIDGE
CH B INPUT
CH B
Manual del usuario / User's manual
1 2 2 3
CSA-300T
CAUTION ATTENTION
RISK OF ELECTRIC SHOCK DANGER D'ELECTROCUTION
DO NOT OPEN NE PAS OUVRIR
CH A INPUT
,
BRIDGE OR
PARALLEL
STEREO
CH A
PARALLEL BRIDGE
CH B INPUT
CH B
3 4
9
SPEAKER
OUTPUT
CHANNEL A
0
70V
BRIDGE
70
1 00V
25V
100
1 40V 200V
100
25V
70
1 00V
70V
0
CHANNEL B
4 5
9 10
F
8T
ACTOR
10x
SPEAKER
OUTPUT
CHANNEL A
0
70V
BRIDGE
FOR CONTINUED PROTECTION
70
1 00V AGAINST RISK OF FIRE REPLACE
ONLY WITH THE SAME TYPE
25V
100 T3.15 A 250V FUSE
1 40V 200V
100
25V
70
1 00V
70V
0
CHANNEL B
5
10
F
8T
ACTOR
10x
FOR CONTINUED PROTECTION MODEL: CSA-300T
AGAINST RISK OF FIRE REPLACE 220V-240V 1.7A 50Hz-60Hz
W
ONLY WITH THE SAME TYPE OUTPUT PWR PER CH/IMP: 300W/4
T3.15 A 250V FUSE
S.N. :
EUROPEAN
PRODUCT
N1918
D.A.S. AUDIO S.A. (Valencia)
MADE IN SPAIN
MODEL: CSA-300T
220V-240V 1.7A 50Hz-60Hz
OUTPUT PWR PER CH/IMP: 300W/4 W
S.N. :
EUROPEAN
PRODUCT
N1918
D.A.S. AUDIO S.A. (Valencia)
MADE IN SPAIN
16