Operation - Triton TRPUL Instrucciones De Uso Y De Seguridad

Ocultar thumbs Ver también para TRPUL:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 44
Correct setting of blades
It is essential that the blades are set correctly or the workpiece will end up
rough and uneven. For a clean, smooth cut, the blades must be mounted so
that the cutting edge is absolutely level. i.e. parallel to the surface of the rear
base (b)
Nicks in surface
The cutting edge of one or all blades is not parallel to the rear base
Gouging at start
One or all blades are not protruding enough in relation to the rear base
Fitting the sanding drum (9-12)
• A Triton Sanding Drum (24) and sanding sleeve are supplied for use with
this tool. You can convert the Triton Unlimited Rebate Planer into a sander
by fitting the sanding drum in place of the blade drum
• Replacement sanding sleeves are available from your Triton retailer (Part
no. TRPSS)
• Using the sanding drum and sleeve, this tool is ideal for quickly removing a
large amount of material
• Do not use this sander for sanding steel or magnesium
Fitting a sanding sleeve
The sanding drum is supplied in two sections. Separate the two sections in
order to fit or remove a sanding sleeve
1. Ensure all the rubber 'O' rings are in place
2. Slide the sanding sleeve fully onto the larger section of the sanding drum
(Note: it will only fit on one way)
3. Insert the smaller section of the sanding drum into the sanding sleeve and
align so that the groove in the inner ring of the smaller drum section fits
over the nib on the spigot of the larger section
Fitting the sanding drum in the tool
• Always ensure that the tool is switched off and unplugged from the power
supply before installing or removing a drum
• To fit or remove the sanding drum, use the same method as set out above
for 'Removing the Blade Drum' and 'Refitting the Blade Drum'
Parallel fence guide (13)
1. Fit the Parallel Fence Guide (23) using the fixing angle and the Parallel
Fence Attachment Knob (22)
GB
2. When set at right angles to the planer base, the fence provides a guide to
help control the planing action
8
(a)
(a)
(b)
(a)
(a)
(b)
(a)
(a)
(b)
(a)
(b)
(a)
(b)
(a)
(b)
(b)

Operation

Switching on and off
WARNING: Before plugging the machine into the power socket always check
that the On/Off Trigger Switch (5) and Lock-Off Button (6) work properly
1. Plug in the machine and grip the tool with your index finger on the on/off
trigger switch and thumb on the lock-off button
2. Depress the lock-off button with your thumb and squeeze the on/off trigger
switch, with the rest of your hand gripping the tool. You can release the
lock-off button once the planer has started
3. To stop the tool, release the thumb hold on the on/off trigger switch
4. In order to restart the machine, it is necessary to operate both the lock-off
(b)
button and the on/off switch
Warning: Please note that the planer blades continue to turn for some time
after switching off the planer. Wait until the motor has completely stopped
before setting down the tool to prevent damage to the planer blades or the
surface If you wish to rest the planer on its side, do not rest it on the side
with the vents to prevent dust or chips from getting into the motor
5. When the planer is not to be used for a short period, set the depth control
knob to the 'P' position and rest the front of the planer on a block of wood
to keep the base clear of the surface. Ensure that the rear parking foot is
down to protect blades
(b)
Adjusting the speed
The speed of the drum can be adjusted to suit the material being planed or
sanded.
Use the Variable Speed Control (25) to adjust the speed for the job in hand.
Note: For planing it is recommended to have the planer running at full speed to
obtain the cleanest possible result.
When sanding, the speed should be set from 1-6; on 'MAX' (maximum speed),
the unit will vibrate and be hard to hold.
Adjusting the depth of cut
1. Rotate the Depth Adjustment Dial (1) clockwise for a deeper cut and
anticlockwise for a shallower cut
2. The calibrations on the ring under the Depth Adjustment Dial indicate the
depth of cut. For example, when '1' is next to the pointer on the front of the
planer, the depth of cut is approximately 1mm
3. If depth of cut is critical, plane a scrap piece of wood, measure the
difference in thickness and adjust the setting as needed

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido