Turning Off Y Our Iron; Maintaining Y Our - Sunbeam 3016 Manual De Instrucciones

will turn from black to red, indicating that the iron is too hot to store. When the iron is turned off, it will take the
iron approximately 30–40 minutes for the STORAGE STRIP
the iron is cool enough to store.
CAUTION: The STORAGE STRIP
handled and stored with care.
T O y I
URNING FF OUR
1. Turn the Variable Steam Lever to (Dry) and Fabric Select to OFF.
2. Unplug the iron from the power source.
WARNING: NEVER yank the power cord when unplugging the iron. This can damage the cord.
1. Turn off iron and unplug from outlet as noted above. Allow the iron to cool.
2. E mpty the water reservoir after each use for a longer iron life. To do so, unplug the iron, turn the iron upside
down, open the fill hole cover, and allow water to flow from the fill hole. Shake the iron gently to remove
trapped water drops.
3. I f your iron does not have a retractable cord, loosely loop the power cord around the heel rest and store the iron
on its heel rest.
IMPORTANT: Wrapping the cord around the iron too tightly can damage the cord.
Tip: When not ironing, always set the Variable Steam Lever to (Dry) and the Fabric Select to OFF.
c S
lEANING ThE OlEPlATE
Clean the soleplate if starch or other residue accumulate.
To clean the Soleplate:
1. T urn off iron and unplug from outlet as noted above. Allow the iron to cool and then wipe it with a soft, damp
cloth.
WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean the soleplate. This will damage
the finish.
2. Run the iron over an all-cotton cloth to remove any residue.
U T S -c
SING hE ElF lEANING
You should use the Self-Cleaning feature once a month to maintain the optimal performance of your iron.
T S -c
O USE ThE ElF lEAN FEATURE
1. T urn off iron following instructions above. (See Caring For Your Iron After Use Instructions)
2. Move the Variable Steam Lever back and forth from
and minerals from the Variable Steam Valve. This keeps water flowing into the steam chamber
3. Fill the water reservoir with tap water to the MAX line.
4. Set the Fabric Select to Linen.
5. Plug the iron into a power outlet and allow the iron to heat for 2 minutes.
6. Allow iron to cool, then turn the Fabric Select to Off then unplug the iron.
7. Allow iron to cool, then hold the iron over a sink in a horizontal position.
WARNING: Be careful not to touch the iron's hot surfaces.
8. P ress the Self-clean Button and hold. Water will begin dripping from the steam vents. To make sure that all of
the water is removed from the tank, slowly rock the iron side to side and front to back for 30 seconds. When
rocking the iron, dip the nose of the iron slightly below the rear of the iron to make certain the water circulates
completely. Release Self-Clean button after one minute.
9. T urn the iron upside down and allow the remaining water to flow out of the fill hole.
10. Dry the soleplate with a towel.
11. P lug in the iron and set the Fabric Select to Linen. Let the iron heat for 2 minutes to dry out the iron completely.
12. Set the Fabric Select to the Off, unplug the iron, and allow it to cool.
indicator should only be used as a guideline. The iron should always be
®
c
ARING FOR
RON
S
TORING
M
AINTAINING
F (On Select Models Only)
EATURE
:
Indicator to turn from red to black, indicating that
®
y I A
OUR RON FTER
y I
OUR RON
y c I
OUR lASSIc RON
(Dry) to (Max Steam) several times to remove debris
English - 4
U
SE