Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
•
Do not place any object on top of the charger or
place the charger on a soft surface that might block
the ventilation slots and result in excessive internal
heat. Place the charger in a position away from any heat
source. The charger is ventilated through slots in the top
and the bottom of the housing.
•
Do not operate the charger with a damaged cord
or plug.
•
Do not operate the charger if it has received a sharp
blow, been dropped or otherwise damaged in any
way. Take it to an authorized service center.
•
Do not disassemble the charger; take it to an
authorized service center when service or repair
is required. Incorrect reassembly may result in a risk of
electric shock, electrocution or fire.
•
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
this risk.
•
NEVER attempt to connect 2 chargers together.
•
The charger is designed to operate on standard
120V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicular charger.
WARNING:
the charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior of the
charger using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.
WARNING:
any liquid to get inside the charger. Electric shock
may result.
WARNING:
submerge the battery pack in any liquid or allow any
liquid to enter the battery pack. Never attempt to open
the battery pack for any reason. If the plastic housing
of the battery pack breaks or cracks, return to a service
center for recycling.
CAUTION:
of injury, charge only BLACK+DECKER rechargeable
battery packs. Other types of batteries may
overheat and burst resulting in personal injury and
property damage.
CAUTION:
with the charger plugged into the power supply, the
charger can be shorted by foreign material.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
6
Shock hazard. Disconnect
Shock hazard. Do not allow
Burn hazard. Do not
Burn hazard. To reduce the risk
Under certain conditions,
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery pack in an air temperature below +40 °F
(+4.5 °C), or above +104 °F (+40 °C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charging a Battery
Use only with BLACK+DECKER BDCAC60B Series chargers.
1. Plug the charger into an appropriate outlet before
inserting battery pack.
2. Insert the battery pack into the charger, making sure
the battery pack is fully seated in the charger. The
charging light will blink continuously indicating that the
charging process has started.
3. The completion of charge will be indicated by the light
remaining ON continuously. The battery pack is fully
charged and may be used at this time or left in the
charger.
nOTE: To ensure maximum performance and life of lithium-
ion battery packs:
Charge the battery pack fully before first use.
-
-
Recharge discharged batteries as soon a possible
after every use.
Do not discharge batteries fully.
-
Charger Diagnostics
Refer to the indicators below for the charge status of the
Publicidad
Tabla de contenido
