Tripp-Lite OMNISMT700M Guia De Inicio Rapido

This document explains the most important features of your UPS system. For additional information,
download the Owner's Manual PDF (in English or Spanish) from www.tripplite.com/support/manuals
Quick Installation
1 Plug the UPS into a properly grounded outlet: Please Note! The UPS will not turn ON automatically in the presence of live utility power.
To Turn the UPS ON: Press and hold the "ON/OFF/MUTE/TEST" button until you hear the system beep and then release the button. The system is now
turned ON.
To Mute the UPS: Quickly press the "ON/OFF/MUTE/TEST" button until you hear a short chirp and then release the button. The system is now muted.
To Run a Self-Test: Press and hold the "ON/OFF/MUTE/TEST" button until you hear a long, sustained beep and then release the button. The system will now
perform a self-test.
To Turn the UPS OFF: Press and hold the "ON/OFF/MUTE/TEST" button. You will hear a short chirp, followed by a beep, then release the button. The system
is now turned OFF.
2 Plug your equipment into the UPS: Select outlets (see diagram) will provide battery backup and surge protection; plug your computer, monitor and other
critical devices here.* Select outlets (see diagram) will provide surge protection only; plug your printer and other non-essential devices here.
Note: UPS system will function properly upon initial startup; however, maximum runtime for the unit's battery will only be accessible after it has been charged for
24 hours.
* Your UPS is designed to support electronic equipment only. You will overload the UPS if the total VA ratings for all the equipment you connect to the Battery Backup Protected/Surge Protected outlets
exceeds the UPS's Output Capacity. To find your equipment's VA ratings, look on their nameplates. If the equipment is listed in amps, multiply the number of amps by 120 to determine VA. (Example: 1 amp ×
120 = 120 VA). If you are unsure if you have overloaded the Battery Backup Protected/Surge Protected outlets, run a self-test.
Basic Operation
ON/OFF/MUTE/ LINE POWER
TEST Button LED
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed
during the installation, operation and storage of all Tripp Lite UPS
Systems. Failure to heed these warnings may affect your warranty.
UPS Location Warnings
• Install your UPS indoors, away from excess moisture or heat,
conductive contaminants, dust or direct sunlight.
• For best performance, keep the indoor temperature between 32º F and
104º F (0º C and 40º C).
• Leave adequate space around all sides of the UPS for proper ventilation.
UPS Connection Warnings
• Connect your UPS directly to a properly grounded AC power outlet. Do
not plug the UPS into itself; this will damage the UPS.
• Do not modify the UPS's plug, and do not use an adapter that would
eliminate the UPS's ground connection.
• Do not use extension cords to connect the UPS to an AC outlet.
• If the UPS receives power from a motor-powered AC generator, the
generator must provide clean, filtered, computer-grade output.
Equipment Connection Warnings
• Use of this equipment in life support applications where failure of this
equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness
is not recommended. Do not use this equipment in the presence of a
flammable anesthetic mixture with air, oxygen or nitrous oxide.
• Do not connect surge suppressors or extension cords to the output
of your UPS. This might damage the UPS and may affect the surge
suppressor and UPS warranties.
Battery Warnings
• Your UPS does not require routine maintenance. Do not open your UPS
for any reason. There are no user-serviceable parts inside.
• Batteries can present a risk of electrical shock and burn from high
short-circuit current. Observe proper precautions. Do not dispose of
the batteries in a fire. Do not open the UPS or batteries. Do not short
or bridge the battery terminals with any object. Unplug and turn
off the UPS before performing battery replacement. Use tools with
Quick Start Guide
OMNISMT700M
Not suitable for mobile applications.
OVERLOAD LED BATTERY POWER
LED
insulated handles. There are no user-serviceable parts inside the UPS.
Battery replacement should be performed only by authorized service
personnel using the same number and type of batteries (Sealed
Lead-Acid). The batteries are recyclable. Refer to your local codes for
disposal requirements or visit www.tripplite.com/UPSbatteryrecycling
for recycling information. Tripp Lite offers a complete line of UPS
System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the
Web at www.tripplite.com/support/battery/index.cfm to locate the
specific replacement battery for your UPS.
• Do not attempt to add external batteries to the UPS.
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly approved
by Tripp Lite could void the user's authority to operate this equipment.
Copyright © 2010 Tripp Lite. All rights reserved.
REPLACE Battery Backup/
BATTERY LED Surge Protected
Outlets
Surge-Only Tel/DSL Jacks
Protected with Built-In
Outlets Splitter
FCC Part 68 Notice (United States Only)
If your Modem/Fax Protection causes harm to the telephone network,
the telephone company may temporarily discontinue your service. If
possible, they will notify you in advance. If advance notice isn't practical,
you will be notified as soon as possible. You will be advised of your
right to file a complaint with the FCC. Your telephone company may
make changes in its facilities, equipment, operations or procedures that
could affect the proper operation of your equipment. If it does, you
will be given advance notice to give you an opportunity to maintain
uninterrupted service. If you experience trouble with this equipment's
Modem/Fax Protection, please visit www.tripplite.com/support for
repair/warranty information. The telephone company may ask you to
disconnect this equipment from the network until the problem has been
corrected or you are sure the equipment is not malfunctioning. There
are no repairs that can be made by the customer to the Modem/Fax
Protection. This equipment may not be used on coin service provided
by the telephone company. Connection to party lines is subject to state
tariffs. (Contact your state public utility commission or corporation
commission for information.)
Tripp Lite follows a policy of continuous improvement. Product
specifications are subject to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
USB Port
201006152 • 933033-EN