Extension Cords - Genesis GPCS535CK Manual Del Operario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

EXTENSION COrDS

Grounded tools require a three wire extension cord
use either a two or three wire extension cord. As the distance from the power supply outlet increases, you must
use a heavier gauge extension cord. using extension cords with inadequately sized wire causes a serious drop
in voltage, resulting in loss of power and possible tool damage. Refer to the table shown below to determine the
required minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord. for example: a 14-gauge cord
can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total
length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord
for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire
size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A" ("W" in Canada) to
indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Recommended Minimum Wire Gauge for Extension Cords (120 Volt)
Nameplate
Extension Cord Length
Amperes
25 Feet
(At Full Load)
0–2.0
18
2.1–3.4
18
3.5–5.0
18
5.1–7.0
18
7.1–12.0
18
12.1–16.0
14
16.1–20.0
12
SPECIFIC SAFETY rULES FOr PLUNGE CIrCULAr SAWS
WArNING:
(GAINED FrOM rEPEATED USE) rEPLACE STrICT ADHErENCE TO PrODUCT SAFETY
rULES. If you use this tool unsafe or incorrectly, you can suffer serious personal injury!
WArNING:
operation where cutting tools may contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live" and shock the operator!
DANGEr!
Keep hands away from cutting area and blade
to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump
backwards. (See "Causes and Operator Prevention of Kickback") Do not reach underneath the work. The
guard cannot protect you from the blade below the work. Do not attempt to remove cut material when blade
is moving.
CAUTION:
Blades coast after turn off. Wait until blade stops before grasping cut material.
• Check the operation and condition of the lower guard spring.
spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due
to damaged parts, gummy deposits, or a buildup of debris.
• Always observe that the lower guard is covering the blade
on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is
in its path. Be aware of the time it takes for the blade to stop after switch is released.
• Never hold piece being cut in your hands or across your leg.
support the work properly to minimize body exposure, blade binding, or loss of control.
50 Feet
75 Feet
18
18
18
16
14
12
10
DO NOT LET COMFOrT Or FAMILIArITY WITH PrODUCT
Hold tool by insulated gripping surfaces when performing an
100 Feet
18
18
18
16
16
14
14
12
12
10
10
10
8
8
.
Double insulated tools can
150 Feet
200 Feet
16
16
14
14
12
12
12
10
8
8
8
6
6
6
.
Keep your body positioned
If the guard and the
before placing saw down
It is important to
5

Publicidad

Tabla de contenido
loading

Tabla de contenido