Parker Hiross Hypercool ADS000 Manual De Uso página 4

4. Installation (see. Fig. 4 a/b/c)
Indoor positioning
Always guarantee a suffi cient air fl ow as follows (see Fig. 1):
• Provide an appropriate air inlet and outlet (open window or
other).
• If possible place the aft erccoler's air intake up against the air
inlet for maximum cooling (leave a 500mm gap between aft er-
cooler and wall to allow fan servicing).
• Never place the aft ercooler's air inlet near the (hot) air com-
pressor.
Outdoor positioning
When positioning the aft ercooler outdoors, respect the following
guidelines (see Fig. 2):
• It is recommended to position the unit under an overhead
protection.
• Avoid positions where leaves and other impurities can be
sucked into the air intake.
• Provide a thermostatic fan shut-off device (stop = 3°C, restart
= 6°C) on the aft ercooler's compressed air outlet to prevent any
condensate in the air from freezing.
In order to guarantee the stability of the equipment even in the
case of wind or adverse atmospheric conditions, it must be an-
chored to the ground using suitable fi xing devices, to be applied to
the holes provided for this purpose at the base of the legs.
ALWAYS INSTALL THE AFTERCOOLER WHERE THERE IS
THELOWEST POSSIBLE AMBIENT AIR TEMPERATURE.
a) Install the unit only in environments which ensure an
ambient temperature within the range specifi ed on the data
plate. Th ese limits must be observed in all cases.
b) Install one or more safety valves as necessary on the air/
gas side to ensure that maximum design pressure is never
exceeded. Th ese valves must be fi tted in such a way that there
is no risk of any expelled fl uid coming into contact with
operators.
c) If the pressurised fl uid circuit is subject to vibration, use
fl exible hoses and vibration dampers to connect up the unit, or
secure the circuit more fi rmly to eliminate the vibrations.
If the circuit is subject to pressure pulses of more than 10%
rated pressure, install a pulse damper to reduce them to below
this level.
d) Make sure that the air around the unit does not contain con-
taminating solids or gases. Compressed and condensed gases
can react to produce acids and other chemicals which could
damage the unit.
Take particular care with sulphur, ammonia, chlorine and
installations in marine environments. For further advice or as-
sistance consult the manufacturer.
e) Support the air/gas inlet and outlet pipes if they strain the
connection ports and/or fl anges.
f) If the unit is installed in a seismic zone, install suitable devices
to protect against seismic activity.
g) Install fi re-prevention and fi re-fi ghting equipment suitable
for the area in which the unit is installed in order to protect it
against fi re.
h) If operating temperature exceeds 60°C, fi t any protective
guards necessary to prevent accidental contact and burns.
2
RESPECT THE DIRECTION OF THE AIR/WATER IN-
LET AND OUTLET LABELS.
AIR CONNECTIONS: Attach the compressed air piping to the
threaded/fl anged connections on the apparatus.
Th e apparatus must be installed immediately downstream of the
compressor, and with the separator downstream of the aft ercooler.
BY-PASS: Install a by-pass line with its own shut-off valve (4 - Fig.
1/Fig. 2) as well as shut-off valves on both the aft ercooler inlet and
outlet (5 - Fig. 1/Fig. 2).
5. Operation
FOR SEPARATOR SEE RESPECTIVE MANUAL.
Th e temperature of incoming fl uids, must never exceed the maxi-
mum value specifi ed on the data plate. If temperatures exceed the
specifi ed values, contact the manufacturer for further information.
Avoid subjecting the unit to thermal stress caused by repeated
fl uctuations in incoming fl uid temperature.
To guarantee optimum operation, ensure that the maintenance
program below is performed regularly, and that the following rules
are respected:
• Ensure a constant air fl ow through the aft ercooler coil.
• Drain all water out of the aft ercooler when it is not in opera-
tion (to prevent ice formation).
ADS/ADT/ADW English