cecotec CONGA 5090 Manual De Instrucciones página 19

ENGLISH
Remote control installation
If the robot does not respond to the remote control, follow the below steps:
Press the edge mode button on the remote control for 5 seconds for the remote control to
enter pairing mode. The display will show 8888.
The remote receiver will be activated in 5 seconds and will enter pairing mode. The remote
control's signal is received and the remote control returns to normal status. The display will
show pairing is completed.
If the pairing process is unsuccessful, the remote control will display 8888 and will exit the
pairing mode after 30 seconds.
The following operations and modes can be activated from the remote control:
Modes
The first time the robot is operated, it will map and save the whole house's map by means of
itslaser before starting the cleaning cycle. Use the robot in auto mode and eco power level,
thisway you will ensure the robot memorizes the map completely.
Note: Make sure the light indicator is lighted in blue before starting cleaning, indicating it is
activated. If it is not, press any button on the remote control to wake it up.
Auto mode
Press the power button on the robot for it to start cleaning automatically, first a cleaning cycle
in Edge mode and then another cycle in an organized zig zag motion, recognizing which areas
it has cleaned and which ones it has not. The robot will plan the cleaning route automatically
as it is cleaning. If during this mode the robot is controlled manually, the robot will calculate
the route again and could go through previously cleaned areas. In order to ensure efficient
cleaning, do not operate it manually during auto mode cleaning.
Fig. 17
Thanks to its TotalSurface 2.0 technology, if the battery is low during the cleaning cycle, the
robot will smartly return to the charging base automatically and, once it is fully charged, it will
resume the cleaning process from the same point, offering a high-efficiency cleaning. During
cleaning, the robot will stop briefly to evaluate the area and calculate the cleaning route (this
stop will vary depending on the house conditions).
Warning: The robot cleans in an organized way and per 4x4 m squared areas, therefore it
might leave the room where it is cleaning to finish off the delimited area. Do not worry, the
robot will clean all the accessible surface.
Edge mode
Press the edge button on the remote control for the robot to start cleaning under this mode. It
will automatically start cleaning along all the surface's perimeters and then will return to the
charging base direct and automatically. If the robot has not started cleaning from the charging
base, it will return to the starting point.
Note: Press the Power button to switch between the 3 modes: Turbo/Normal/Eco.
Fig. 18
36
Back home mode
Press the home button on the robot in order to send the robot to the charging base. This mode
can be activated during any other cleaning cycle and the robot will stop cleaning and return
to the charging base automatically. The robot will take the shortest route back to the charging
base thanks to its map memorizing and its smart back-home function.
When a cleaning cycle has been completed or the robot's battery is low, thanks to its
TotalSurface 2.0 technology, the robot will also return to the charging base to avoid running
out of battery. Once the robot has charged, it will resume cleaning from the exact point where
it has stopped.
Warning:
Remove the Wet & dry tank from the robot before charging it.
Make sure there are no obstacles in the room being cleaned to ensure the robot can get to the
charging base without problems.
Fig. 19
Functions
Pause
While the robot is operating, press the power button on the App, the remote control or on the
robot to pause it and press the power button again to resume cleaning.
Standby
The robot will automatically enter standby mode after 5 minutes of no operation.
Press on the App, the remote control or on the robot to start it up again.
Warning:
After 12 hours of no operation, the robot will turn automatically off.
The robot will not enter standby mode during charging.
Suction power level
Press on the remote control or on the App to select the desired power level. Choose between
Eco (low power), Medium (medium power) and Turbo (maximum power).
Scheduling
Warning: The robot cannot be scheduled from more than one device at a time. Make sure to
schedule it either from the mobile phone App or from the remote control.
The robot is provided with a schedule function in order to provide a maximum-efficiency
cleaning. The time settings and the cleaning schedules must be carried out from the remote
control. Once the robot has been scheduled, it will automatically carry out the cleaning cycles
every scheduled day.
Note: Make sure the robot is activated and that the light indicator is lighted before scheduling
any cleaning or setting time.
ENGLISH
37