Rotel RC-995 Manual De Instrucciones página 10

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
RR-949 Remote Control
The RC-995 includes a hand held remote control that does more
than operate the RC-995. The RR-949 is a full-function pro-
grammable remote control that can operate up to 8 audio/video
components.
A separate manual, included with the remote, gives detailed infor-
mation on programming and use of the RR-949 to replace all of the
remote controls in your system. This section provides only the in-
formation which pertains to the use of the RR-949 with the RC-995.
Note: Many functions duplicate the RC-995 front panel controls
and are listed here only for your reference. Please refer to the
Front Panel Controls section of this manual for detailed informa-
tion.
Programming the RR-949
The RR-949 must be programmed before it is used to control the
RC-995.
Step One: First you must assign one of the Device Selection but-
tons to the RC-995. In this example we are assigning the Au-
18
dio button ("AUD") to the RC-995. Press the AUD button at the top
of the remote while simultaneously pressing the Mute button
and hold both for at least one second. The next step must be done
within 20 seconds period, or the RR-949 will revert to its standard
operating mode.
Step Two: Use the Numeric Buttons
For the RC-995 press 001; or 002 if you are using the RR-949 with
the RT-940. Press each digit of the code separately.
Step Three: Store the code number by pressing the AUD button
again.
Following this programming the RR-949 will operate the RC-995 af-
ter you press the AUD button. It will continue to do so until an-
other Device Selector button is pressed, which will make the
RR-949 control the component assigned to that button.
Device Selector Buttons
Press one of these button to select the component the RR-949 will
control.
10
STEREO CONTROL AMPLIFIER RC-995
to enter the 3-digit code.
22
18
Power Button
Duplicates the function of the front panel Standby switch. Press
the button to activate the RC-995. Press again to deactivate it.
Volume Buttons
These buttons duplicate the function of the front panel volume
control. Press Volume Up to increase the volume and press Vol-
ume Down to decrease the volume.
Mute Button
21
Press this button to mute the sound. Press it again to restore nor-
mal sound output. The LED in the Volume Control will flash when
the unit is muted.
Input Select Buttons
Two rows of buttons which duplicate the function of the Listening
Selector control on the RC-995 front panel. Select an input source
by pressing the corresponding button.
Numeric Buttons
Ten buttons, labeled 1 through 10. Used with the RC-995 only when
entering the 3 digit address code during initial programing.
21
18
19
21
22
23
19
20
23
22
AUD CD TAPE DVD
SAT TV VCR CBL
POWER
20
VOL CH
BAND
MUTE T/V
PRESET TIME/PRESET
SURROUND+ ON SCREEN
GUIDE MENU
PAUSE
TRACK– TRACK+
S S
E E
A PLAY A
R R
SEL
C C
H H
UP DOWN
STOP
PRE.
RECALL CH
OPN/CLS SUR DELAY
1 2 3
MOVIE FIL
DISC1 DISC2 DISC3 PROG
4 5 6 5.1
DISC4 DISC5 DISC6 TIME/REVIEW
7 8 9
SELECT
CLEAR/SCAN
10 0 ENTER BACK
RANDOM/REPEAT
CD TUNER AUX1/V5 AUX2/V5 PHONO
TAPE1 TAPE2 VIDEO1 VIDEO2 VIDEO3
PTY TA TP DISP
SHIFT ZONE
OFF REC
RR949