Follow These Steps When Battery Is Outside Vehicle; Grounding And Ac Power Cord Connections; Assembly Instructions; Control Panel - Schumacher Electric SC1307 Manual Del Usuario

7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE

WARNING: A SPARK NEAR THE
BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF
A SPARK NEAR THE BATTERY:
7.1 Check polarity of battery posts. POSITIVE
(POS, P, +) battery post usually has a larger
diameter than NEGATIVE (NEG, N, –) post.
7.2 Attach at least a 24-inch long 6-gauge
(AWG) insulated battery cable to
NEGATIVE (NEG, N, –) battery post.
7.3 Connect POSITIVE (RED) charger clip to
POSITIVE (POS, P, +) post of battery.
7.4 Position yourself and free end of cable as
far away from battery as possible – then

8. GROUNDING AND AC POWER CORD CONNECTIONS

8.1 This battery charger is for use on a
nominal 120 volt circuit. The charger
must be grounded, to reduce the risk of
electric shock. The plug must be plugged
into an outlet that is properly installed
and grounded in accordance with all local
codes and ordinances. The plug pins
must fit the receptacle (outlet). Do not use
with an ungrounded system.
8.2 DANGER: Never alter the AC cord or
plug provided – if it does not fit the outlet,
have a proper grounded outlet installed
by a qualified electrician. An improper
connection can result in a risk of an
electric shock or electrocution.
NOTE: Pursuant to Canadian
Regulations, use of an adapter plug
is not allowed in Canada. Use of an

9. ASSEMBLY INSTRUCTIONS

9.1 Remove all cord wraps and uncoil the
cables prior to using the battery charger.
9.2 Included with your charger are two cord
wrap cleats for storage of the clamp

10. CONTROL PANEL

DIGITAL DISPLAY
The Digital Display gives a digital
indication of voltage or % of charge. The
display will show the battery VOLTAGE
when the charger is not charging a
battery. When it goes into charging mode,
the display will automatically change to
ON (to show charging has started) and
then show the percent-of-charge of the
battery being charged and either 6 or
12 (the battery voltage determined by
the charger). If you manually stop the
charging process (by pressing the Rate
Selection button) before the battery is fully
charged, the display will show OFF.
connect NEGATIVE (BLACK) charger clip
to free end of cable.
7.5 Do not face battery when making final
connection.
7.6 When disconnecting charger, always do
so in reverse sequence of connecting
procedure and break first connection
while as far away from battery as
practical.
7.7 A marine (boat) battery must be removed
and charged on shore. To charge it on
board requires equipment specially
designed for marine use.
adapter plug in the United States is not
recommended and should not be used.
8.3 USING AN EXTENSION CORD
The use of an extension cord is not
recommended. If you must use an
extension cord, follow these guidelines:
• Pins on plug of extension cord must be
the same number, size, and shape as
those of plug on charger.
• Ensure that the extension cord is
properly wired and in good electrical
condition.
• Wire size must be large enough for the
AC ampere rating of charger, as specified:
Length of cord (feet)
AWG* size of cord
*AWG-American Wire Gauge
cables. To install, align the two tabs with
the two receptacles on the back of the
charger and push until you hear a snap.
NOTE: During charging, the display will
go into sleep mode and will not show the
percentage of charge or voltage of the
battery. To turn the display back on, press
the Display button.
DISPLAY BUTTON
Use this button to set the function of the
digital display to one of the following:
• Battery % – The digital display shows
an estimated charge percentage of
the battery connected to the charger's
battery clamps.
• Voltage – The Digital Display shows the
voltage at the charger battery clamps, in
DC volts.
• 5 •
25 50 100 150
16 14 14 12