Digital Audio Input Connections; Using A Usb Cable To Connect To A Computer; Using Centralized Control With Other Pioneer Components; Plugging In - Pioneer A-70DA-K Manual De Instrucciones

Amplificador integrado
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 82
Connecting up

Digital audio input connections

If you connect the DIGITAL IN terminal of the unit and
the digital audio output of a digital audio device with a
separately sold digital cable, you can play the audio of
the digital audio device with the unit.
For details on the output of audio input to the DIGITAL
IN terminal, refer to page 11.
DIGITAL OUT
COAXIAL
Digital audio
equipment, etc.
Coaxial digital audio cable
(sold separately)
BALANCED IN
CED IN
PHASE
PHASE
NORMAL
NORMAL
INVERSION
INVERSION
USB
USB
COAXIAL
COAXIAL
LINE2
LINE2
OUT
OUT
OPTICAL
OPTICAL
LINE2
LINE2
Optical digital audio cable
(sold separately)
LINE1
LINE1
ANALOG IN
G IN
DIGITAL IN
DIGITAL IN
A-70DA's rear panel
DIGITAL OUT
OPTICAL
Digital audio
equipment, etc.
Note
• Digital signal formats that can be input to this unit
include linear PCM signals with sampling rate and
quantitative bits up to 192 kHz/32 bits. (Depending
on the connected device and environment,
operation may not be successful).
Using a USB cable to connect to a
computer
If a USB cable (sold separately) is used to connect this
unit's DIGITAL IN USB terminal to a computer's USB
port, music files located on the computer can be played
through this unit.
For more information regarding the output of audio
signals input to the DIGITAL IN USB terminal, consult
page 13.
Important
• A dedicated driver needs to be installed on your
computer (page 13).
USB
PC
A-type
USB cable
(sold separately)
BALANCED IN
CED IN
PHASE
PHASE
NORMAL
NORMAL
INVERSION
INVERSION
USB
USB
COAXIAL
COAXIAL
B-type
LINE2
LINE2
OUT
OUT
OPTICAL
OPTICAL
LINE2
LINE2
LINE1
LINE1
ANALOG IN
G IN
DIGITAL IN
DIGITAL IN
A-70DA's rear panel
Note
• This unit cannot be used to play audio files from a
computer unless Media Player is installed on the
connected computer.
Using centralized control with other
Pioneer components
Multiple Pioneer components equipped with CONTROL
IN/OUT jacks can be connected to the unit, allowing
centralized control of the components via the remote
sensor on the unit. This also allows remote control of
components not equipped with a remote sensor, or
installed in places where the component's remote
sensor cannot be accessed.
IN
OUT
To other Pioneer
CONTROL
component
equipped with
CONTROL IN jack
Other Pioneer
component equipped
with CONTROL IN/
OUT jacks
A-70DA
Aim remote control
Remote
at the sensor on the
control
unit.
Note
• For connections use a commercially available
monaural miniplug cord (without resistor).
• When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be
used to make analog connections. Merely
connecting the CONTROL IN/OUT jacks alone will
not allow proper system control.
• When a control cord is connected to the unit's
CONTROL IN jack, the unit cannot be controlled by
pointing the remote control at the unit (the remote
sensor is automatically disabled).

Plugging in

Important
• When going on a trip or otherwise not using the
unit for an extended period, always disconnect the
power cord from its outlet. Note that various
internal settings will not be lost even if the power
cord is disconnected from its outlet for an extended
time.
• If it is necessary to detach the power cord, first be
sure to press the /I STANDBY/ON button on the
front panel of the unit so the unit is turned OFF
before detaching the cord.
Caution
• The use of a power cord other than the one provided
will invalidate the warranty, since Pioneer will not
be responsible for any damage incurred. (The
power cord provided with the unit has a rated
current capacity of 10 A.)
• Do not use any power cord other than the one
supplied with this unit.
• Do not use the supplied power cord for any purpose
other than that described below.
After you've finished making all connections, plug the
unit into an AC outlet.
This unit's rear panel
To AC outlet
Power cord
(included)
1
Plug the supplied power cord into the
AC IN socket on the rear panel of the unit.
2
Plug the other end into an AC outlet.
02
7
En

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

A-50da-kA-70da-sA-50da-s

Tabla de contenido