Outputs; Master Thru And Cue Master Thru; Device Settings & Tests; Menu For Midi Channel Assignment And Jog Wheel Resolution Adjustments - Reloop Jockey 3 Remix Manual De Instrucciones

4.4 Outputs

The Jockey 3 Remix disposes of three stereo output channels on the device's rear side.
Master 2 -B63- as RCA output as well as Master 1 -B62- as symmetrical 6.3 mm jack output are adjusted via the Master Volume Dial -T37-.
The Booth Output -B64- as RCA output is adjusted via the Booth Dial -T38-.

4.5 Master Thru and CUe Master Thru

The Master Thru function is especially convenient for setups with 2 DJs. The second DJ's output signal is emitted via the 3.5 mm jack -B61- through
the Jockey 3 Remix to master. If you wish to monitor the signal at the Jockey 3 Remix, the monitoring function can be activated with the Cue
Master Thru Switch -F53-.
5. device Settings & Tests
A few adjustments and tests can be carried out with the Jockey 3 Remix directly, without the need for a computer. In the following a few items
are explained in detail.

5.1 Menu for MIdI Channel Assignment and Jog Wheel Resolution Adjustments

In order to access the setup menu proceed as follows:
1. Make sure that the Jockey 3 Remix is turned off (see position On/Off Button -B56-).
2. Press and hold the Shift Button -T25- and turn on the Jockey 3 Remix via the On/Off Button -B56-.
3. Now release the Shift Button -T25-.
Now you have the possibility to adjust the MIDI channel assignment and the jog wheel resolution.

5.1.1 MIdI Channel Assignment

NOTE! By default the Jockey 3 Remix is configured for MIDI channels 1-4. Deck A is assigned to channel 1, Deck B is assigned to channel 2,
Deck C is assigned to channel 3 and Deck D is assigned to channel 4. Reloop's official mappings are laid out for the standard configuration. An
adjustment is usually not necessary.
However, if you wish to switch the decks to the MIDI channel combinations 5-8, 9-12 or 13-16, please proceed as follows:
1. By pressing the left FX Dry/Wet Encoder you will access the MIDI channel assignment menu.
2. Via the CUE Pads 1-4 -T20- it is now possible to adjust the MIDI channels. The corresponding Cue Pad is illuminated while the other Cue Pads
are blinking.
MIdI CHAnneL COMBInATIOn
1 – 4
5 - 8
9 - 12
13 - 16
3. When the desired MIDI channels have been selected, it is possible to store these permanently by pressing the Shift Button -T25-.

5.1.2 Jog Wheel Resolution

If Traktor Pro 2 is being used, an adjustment of the jog wheel resolution is not necessary. However, not every software supports the high resolution
of the Jockey 3 Remix's jog wheel -T24-. If you wish to adjust the resolution please proceed as follows:
1. By pressing the FX Parameter 1 Encoder -T3- you will access the jog wheel resolution menu. Via the CUE Pads 1-4 -T20- the jog wheel resolution
can be adjusted. The corresponding CUE Pad is illuminated while the remaining CUE Pads flash.
JOG WHeeL ReSOLUTIOn
512
1024
2048
4096
3. When the desired resolution has been selected, it is posible to store it permanently by pressing the Shift Button -T25-.

5.2 Led Function Test

Herewith you can check whether all LEDs that have been integrated in the Jockey 3 Remix are working correctly. For the function test proceed
as follows:
1. Make sure that the Jockey 3 Remix is turned off (see position On/Off Button -B56-).
2. Press and hold the left Sync Button -T26- and turn on the Jockey 3 Remix via the On/Off Button -B56-.
3. Now release the Sync Button -T26-.
4. Now all LEDs should be lit.
5. In order to complete the test simply turn off the device via the On/Off Button -B56-.
30
CUe PAd BUTTOn
1
2
3
4
CUe PAd BUTTOn
1
2
3
4