Husqvarna HMI Manual De Usuario página 55

Ocultar thumbs Ver también para HMI:
Tabla de contenido

Publicidad

FS 5000D
Control Panel
SN (Serial Number)
HW (Hardware Number)
SW (Software Number)
BL (Bootloader Number)
Engine
Serial Number
Model Number
Engine working hours
Engine working hours in low idle
Time since last regeneration
Engine working hours left until
regeneration must be performed
Modify
Service
Timers
Replace engine oil and filter
Adjust
Service Interval:
New Service Interval:
Select
1247 - 001 - 09.07.2019
System
Information
Gearbox
and Blade
Information
GPL
License
:
2015010001
:
580844701-NA
:
581536001-T
:
581536101-NA
:
NA
:
:
NA
:
5:00 (hh.mm)
:
2:03 (hh.mm)
Clear
:
23:10 (hh.mm)
Low
Idle Time
:
3:00 (hh.mm)
100 hours
100 hours
Hold to
Save
Interval
ENGINE SPEED / BLADE SIZE (FS 5000 D)
BLADE SHAFT
ENGINE SPEED
BLADE
FLANGE
SIZE
SIZE
LOADED
PULLEY
RATED
RPM
SIZE
RPM
14"
4.5"
3200
4.17"
3000
20"
4.5"
2400
4.17"
3000
26"
5"
1870
4.17"
3000
30"
5"
1630
4.78"
3000
36"
6"
1360
5.75"
3000
FS 5000 D, 1-Speed US
FS 5000 D, 1-Speed EU
FS 5000 D, 3-Speed 14-26 US
FS 5000 D, 3-Speed 20-30 US
FS 5000 D, 3-Speed 20-36 US
FS 5000 D, 3-Speed 350-650 EU
FS 5000 D, 3-Speed 500-750 EU
FS 5000 D, 3-Speed 500-900 EU
Setup Menu 2
Press
Button to enter Setup
Menu 1
Modify
Service
Timers
Hold to
Reset
Adjust
Engine
PULLEY
SIZE
6"
Non
Engine
No Active Engine Fault Codes
4.51"
3.50"
3.50"
3.50"
Engine
C1F0521
Non
C1F0522
Engine
U100088
Select
Fault
Codes
Service
Timer
Menu
Callibrate
E-track
Replace engine oil and filter every
100 hours
Service overdue by:
23 hours
Inspect radiator air filter every
50 hours
Time to next service
50 hours
Check blade drive V-belt tension
every 50 hours
Time to next service
50 hours
Lubricate front wheel bearings every
50 hours
Time to next service
50 hours
Replace hydraulic system filter every
50 hours
Time to next service
73 hours
Replace engine oil and filter every
100 hours
Time to next service:
95 hours
Inspect radiator air filter every
50 hours
Time to next service:
45 hours
Check blade drive V-belt tension
every 50 hours
Service overdue by:
2 hours
Lubricate front wheel bearings every
50 hours
Time to next service:
45 hours
Replace hydraulic system filter
every 50 hours
Time to next service:
45 hours
Lubricate front axle pivot bearings
every 100 hours
Time to next service:
95 hours
Active Engine Faults
Non Engine Faults
E-track Motor
Output Current Overload
E-track Motor
Output Current Openload
I/0 Controller
Software Download Failed
Show
PopUp at
Ignition
on
Show
PopUp at
Ignition On
Show
Passive
Faults
Clear
55

Publicidad

Tabla de contenido
loading

Tabla de contenido