Cleaning, Maintenance And Ordering Spare Parts - EINHELL PICOBELLA Manual De Instrucciones

Limpiador de superfi cie inalámbrica
Ocultar thumbs Ver también para PICOBELLA:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

most comfortable for you (see section 5.3).
The splash guard must just clear the ground
on both sides.
3. Actuate the left side (Fig. 20 / Item 25) of the
changeover switch (standard direction of
rotation).
4. Lift the equipment 0.4-0.8 inches (1-2 cm)
and switch on the equipment (see section
6.2).
5. Set the desired speed (from slow to fast)
(see section 6.3). Wait until the full speed has
been reached and then place the brush on
the artifi cial turf. The equipment will pull away
from you.
6. To raise the fi bers upright, brush against the
direction of the fi bers of the artifi cial turf once
the desired speed has been reached. Do not
exert any pressure.
7. If required, draw the brush towards you and
let it roll away without pressure.
8. Repeat this movement until the desired result
has been achieved.
6.5 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.6 Battery capacity indicator (Fig. 19 / item
23)
Press the battery capacity indicator switch (22).
The battery capacity indicator (23) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery pack has been deep-discharged and
is defective. Do not re-use or charge a defective
battery pack.
Anl_Picobella_SPK7_USA.indb 15
Anl_Picobella_SPK7_USA.indb 15
EN
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
We recommend cleaning the equipment
immediately each time after use.
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.3 Ordering replacement parts:
Service
1. If your power tool requires service,
contact an authorized Einhell USA dealer
or call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical
replacement parts should be utilized for
repairs. This will ensure that the safety of the
power tool is maintained.
2. If the battery charger cable is damaged, it
must be immediately replaced to avoid a
hazard. Contact the Einhell USA
service center at 1-866-EINHELL
(1-866-346-4355) for assistance.
MEDIUM replacement brush (nylon, black)
Art. No. 3424123
SOFT replacement brush (nylon, yellow/green)
Art. No. 3424124
ULTRA replacement brush (metal)
Art. No. 3424125
- 15 -
customer
®
01.07.2020 11:37:55
01.07.2020 11:37:55

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

3424210

Tabla de contenido