Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
iMPORTANT
SAFETY iNSTRUCTiONS
WARNING:
To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
•
Read all instructions
before using the dryer.
•
Do not place items exposed to cooking
otis in your dryer.
Items contaminated
with cooking
oils may contribute
to
a chemical reaction that could cause a load to catch fire.
•
Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances
as they give off vapors that could ignite or
explode.
•
Do not allow children to play on or in the dryer. Close
supervision
of children is necessary when the dryer is
used near children.
•
Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
•
Do not reach into the dryer if the drum is moving.
•
Do not install or store the dryer where it will be exposed
to the weather.
•
Do not tamper with controls.
•
Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended
in this
Use and Care Guide or in published user-repair
instructions
that you understand and have the skills to
carry out.
•
Do not use fabric softeners or products to eliminate static
unless recommended
by the manufacturer of the fabric
softener or product.
•
Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
•
Clean lint screen before or after each load.
•
Keep area around the exhaust opening and adjacent
surrounding
areas free from the accumulation
of lint, dust,
and dirt.
•
The interior of the dryer and exhaust vent should be
cleaned periodica!ly
by qualified service personnel.
•
See installation instructions
for grounding requirements.
SAVE THESE iNSTRUCTiONS
IMPORTANT: The gas instatlation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z22& 1/NFPA 54,
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70,
INSTALLATION INSTRUCTIONS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
8" or 10" pipe wrench
8" or 10" adjustable
wrench (for gas
connections)
Flat-blade screwdriver
Adjustable wrench that
opens to 1" (2.54 cm) or
hex-head socket wrench
(for adjusting dryer feet)
v4" nut driver or socket
wrench
•
Level
•
Vent clamps
•
Knife
•
Pipe-joint compound
resistant to LP gas
•
Caulking gun and
compound
(for installing
new exhaust vent)
•
Pliers
•
Tape measure
Parts supplied
Remove parts package from dryer drum. Check that all parts are
included.
4 Leveling legs
Parts needed
Check local codes and with gas supplier. Check existing gas
supply, electrical supply and venting. Read "Electrical
Requirements,"
"Gas Supply Requirements" and "Venting
Requirements"
before purchasing parts.
•
For close-clearance
installations between 31.5" (80.01 cm)
and 37" (93.98 cm), see "Plan Vent System" section for
venting requirements.
I_-
37"
--_1
(93.98
Ore)
Mobile home installations require special parts (listed following)
available for purchase from your local Sears store or Sears
Service Center. For further information, please call
1-800-4-MY-HOME
®(1-800-469-4663).
•
Mobile Home Installation Kit. Ask for Part Number 346764.
•
Metal exhaust system hardware.
NOTE: Do not use leveling legs if installing the dryer on a
pedestal.
Publicidad
Capítulos
Tabla de contenido
Solución de problemas
