KEB COMBIVERT F0 V1.2 Manual De Instrucciones página 126

Annex B - Parameter Summary F0
Operation Parameter
Page 41-44
o.0 : boost 1)
o.1 : minimum reference A 1)
o.2 : maximum reference A 1)
o.6 : acceleration time A 1)
o.8 : deceleration time A 1)
o.13 : input source 1) 2)
o.14 : Delta - Boost 1)
o.15 : Delta - Boost time 1)
o.16 : s-curve acceleration time A 1)
o.17 : s-curve deceleration time A 1)
Parameters for Standard Applications!
1) Parameters that can be changed in parameter
sets 1 to 6!
2) Parameter value is stored only after pressing
"ENTER" twice!
RUN Parameter
Page 37-40
r.0 : prom no.
r.1 : inverter status
r.2 : actual value display
r.3 : set value display
r.4 : output voltage
r.5 : DC voltage
r.6 : DC circuit peak voltage
r.7 : current inverter utilization
r.8 : peak load
Protection Parameter
Page 45-50
P.0 : stall prevention level 1)
P.1 : acc / dec time during stall prevention 1)
P.2 : stall torque characteristic 1) 2)
P.3 : LAD stop load level 1)
P.4 : U/f - function 1)
P.6 : speed search condition 1)
P.7 : automatic retry UP 1)
P.11 : energy - saving mode 1) 2)
P.12 : energy - saving level 1)
P.13 : LAD stop condition 1)
P.14 : LD stop DC voltage level 1)
1)
P.15 : load-dependent set shifting level
Drive Parameter
Page 57-61
d.0 : rated frequency 1)
d.1 : f-mode 1)
d.2 : lower modulation limit 1)
d.4 : rated motor power 1)
d.18 : slip compensation / frequency gain 1)
d.19 : slip compensation / auto torque gain 1)
d.20 : slip compensation / min. frequency 1)
d.21 : slip compensation / max. frequency 1)
d.22 : slip compensation / no-load losses 1)
d.23 : slip comp./load-no-load differ.display
1)
d.24 : number of pole pairs
Customer Parameter
Page 62-70
1)
C.0 : limit of maximum reference A
1) 2)
C.2 : rotation lock
C.4 : condition display
C.5 : noise filter / digital inputs
C.6 : DC level auto set 1)
C.7 : DC-braking mode 1) 2)
C.8 : carrier frequency 1)
C.9 : parameter group lock
C.10 : output voltage stabilization 1) 2)
C.12 : baud rate
C.13 : inverter address
C.14 : zero clamp speed 1)
C.15 : select mode of modulation 1) 2)
C.21 : watchdog time
C.25 : control word activation
C.27 : application selection
r.14 : input terminal status
r.15 : output terminal status
r.18 : bus address display
1)
r.19 : reference setting
1) 2)
r.20 : rotation setting
r.21 : password input
r.22 : select parameter group
r.23 : select parameter set
r.29 : current frequency
Input / Output Handler
Page 51-53
H.0 : presetting mode reference value 1) 2)
H.1 : logic of analog inputs 1) 2)
H.3 : output logic 1) 2)
H.4 : Out 1 - function 1) 2)
H.5 : Out 2 - function 1) 2)
H.7 : input logic 2)
H.8 : In -function parameter set 2)
H.9 : analog output function 1) 2)
H.10 : analog output offset y 1)
1)
H.11 : analog output gain
Free-programmable Parameter Sets
Page 71-74
F.0 : key parameter set no.
F.3 : based on para set
F.4 : global enter
F.5 : clear top parameter set
F.6 : bus parameter set no.
F.7 : save last bus parameter
Information Parameter
Page 75-76
I.0 : inverter type
I.1 : rated inverter current display
I.2 : output frequency limit display
I.3 : error counter OP
I.4 : error counter UP
I.5 : error counter OC
I.6 : error counter OH
I.7 : error counter OL
I.8 : error counter set selection
I.9 : error counter watchdog
ANTRIEBSTECHNIK
Level Parameter
Page 54-56
L.0 : actual value level 1 1)
L.1 : actual value level 2 1)
L.2 : load level 1 1)
L.3 : load level 2 1)
L.6 : DC dynamic braking level 1)
L.7 : DC dynamic braking voltage 1)
L.8 : DC dynamic braking time 1)
L.16 : timer value 1)
L.17 : timer adding value 1)
Profil Parameter
Page 77-79
Pr.5 : malfunction code
Pr.6 : control word
Pr.7 : status word
Pr.8 : nominal speed value
Pr.9 : actual speed value
Pr.10 : speed-min-amount
Pr.11 : speed-max-amount
Pr.16 : acceleration-delta speed
Pr.18 : acceleration-delta time
Pr.25 : deceleration-delta speed
Pr.27 : deceleration-delta time
Pr.37 : speed reference value