Acquisition Of The Measured; Values With The Computer; Functions In The Menu; Graphic Representation - Monacor DTM-506RS Manual De Instrucciones

6) Click the button "STOP" to finish the
program. Click "File" in the menu bar
and then "Exit".

7.3 Acquisition of the measured

values with the computer

If "LOBAT" is displayed next to the but-
ton "STOP" in the menu "THERMO"
(fig. 2), the battery of the thermometer is
exhausted and must be replaced.
For measurements via the computer,
a menu "READING" can be called each
for sensors T1 and T2 and for the tem-
perature difference measurement T1-T2
via the buttons "T1 INPUT", "T2 INPUT",
and "T1-T2". These menus are identical
concerning the functions. Figure 3 on
page 3 shows the menu "T1 READING".
7.3.1 Functions in the
menu "READING"
By clicking the individual buttons in the
menu "READING", the following func-
tions can be activated or switched over
and deactivated again by repeated
clicking:
REL Relative value
enter the reference value next to this
button; the temperature deviation
from this value is shown in the display
field
TYPE Selecting the sensor type [like
button "TYPE" (11 or 14) on the ther-
mometer]
F or C Switching from Fahrenheit to
Celsius and vice versa [like button
°C/°F (4) on the thermometer]
HI/LO After entering a lower limiting
value (line LO) and an upper limiting
value (line HI), click the button. In
case of upper or lower deviations
from these values, the display field of
the menu will blink as a warning.
GRAPH The menu for graphic repre-
sentation of the measurement is
called. See chapter 7.3.2.
To print the menu READING, click "File"
in the menu bar, adjust the printer via
"Printer Setup..." first, if required, and
call the print menu via "Print Window...".
To reset all functions to the initial po-
sition, click "Operate" in the menu bar
and then the menu item "Reinitialize All
To Default".
been opened, click "Windows" in the
menu bar and select the desired window.
upper left button

7.3.2 Graphic representation

By clicking the button "GRAPH" in the
menu "READING", the menu "PLOT" is
displayed:
measurement:
The diagram can be adjusted by select-
ing the two options axis Autoscale:
X axis Autoscale
Y axis Autoscale
If the function HI/LO in the menu
"READING" is activated, the upper limit-
ing value is displayed as a red line and
the lower limiting value as a blue line in
the diagram. Below the scrolling bar, the
green field displays the current tempera-
ture, the red field the upper limiting value
and the blue field the lower limiting
value.
called via the menu bar (see end of
chapter 7.3.1). To select another window
that has been opened, click "Windows"
in the menu bar and select the desired
window. To close the menu "PLOT",
double-click the upper left button
To select another window that has
To close the menu, double-click the
.
T1 PL OT. vi
File Operate Windows
T1 PLOT
22,5
22,0
21,5
21,0
20,5
20,0
11:20:05 11:21:15
X axis Autoscale
22,1
Y axis Autoscale
Menu PLOT
The x-axis (time) au-
tomatically adapts to the total measur-
ing time. If this function is deactivated,
the section of the graph can be displa-
ced with the scrolling bar.
ured value) automatically adapts to
the measured values.
The functions Print and Reset can be
11:22:25 11:23:35
22,1 22,1
The y-axis (meas-
.
GB
19