Audio Player - IMG STAGELINE SD-112RDS/BT Manual De Instrucciones

FM tuner
Button
remote control Function
on the unit
Storing stations
to scan all stations and to store them
one after the other:
Keep button pressed for 2 s until the
 
ASM
figures start to appear on the fre-
quency indication. When the station
CH01
number appears on the dis-
play, all stations have been stored.
to enter the received frequency:
1. Press the button DIRECT.

DIRECT
2. Enter the frequency in MHz, using
the buttons 1 ... 9 and 0.
3. Press the button DIRECT.
station scanning:
Keep button pressed until the figures
start to appear on the frequency indi-
DOWN
 
cation.
UP
fine tuning:
Briefly press button (repeatedly).
to store stations:
1. Set the station (see buttons
DIRECT or DOWN / UP).
Press each of the following buttons

MEMORY within 5 seconds; otherwise, steps
 2 – 4 must be repeated.
MEM
2. Press the button MEM(ORY).
3. Select the station number (see
"Calling up stored stations").
4. Press the button MEM(ORY).
Calling up stored stations
no. buttons
4 4
1 ... 5,

10 5, +5, +5
+5
18 3, +5, +5, +5, +5
22 2, +5, +5, +5, +5, +5
no. buttons
4 4
10 1, 0
18 8, +10 /--
1 ... 9, 0,

22 2, +10 /--, +10 /--
+10 /--
or keep the button +10 /-- pressed for
CH--
2 seconds until
the display, and then enter the num-
ber (two digits).
M-DOWN
 previous / next station number
M-UP
to switch between stereo reception

M / S
and mono reception
Additional information for RDS reception
(shown on the second line of the display)
1 st press of the button:
indication of the programme type
PTY NONE
or *
2 nd press of the button:
information with regard to title / broad-
cast programme or
3 rd press of the button:
indication of the time (after calling up

RDS
the station, it may take a few minutes
until the time is available)
CT NONE
or *
4 th press of the button:
brief indication of the frequency and
the station number, then indication of
the station name (basic setting)
*if the information is not provided
Automatic switch-off of the tuner
1. Press button repeatedly until the
display indicates the desired
length of time after which the tuner
switches off. The tuner will switch
off when the set length of time has
elapsed.
2. To switch the tuner on again:

SLEEP-90
SLEEP
Press button:
appear on the display. Press button
once again; otherwise, the switch-
off function will be activated again.
3. To deactivate the function before
the set length of time has elapsed:
Press button so that the indication
SLEEP
... disappears.

4.3 Audio player

Connect, for example, a USB flash drive or a
hard disk (with separate power supply, if
required) to the USB port
insert a memory card into the slot SD/ MMC
CARD (notched corner pointing upwards and
facing the unit). To remove the card, push the
card into the slot until it disengages.
The audio player can only be operated with
the remote control when the LED "USB / SD"
lights up. If the LED "TUNER" lights up, press the
button TUNER – USB / SD on the remote control.
Notes
1. When the sliding switch PLAY MODE on the rear of
the unit is set to a different position, any change of
function will not take effect until the SD-112RDS / BT
has been switched off and on again.
2. When switching over the replay from the memory
card to the USB storage medium (or vice versa), any
function selected (e. g. repeat function, single title
replay, intro function) will be deactivated. The posi-
tion of the sliding switch PLAY MODE defines if the
replay will start automatically after switching over or
not.
appears on
RT NONE
*
will
Button
and / or remote control
on the unit
PLAY
MODE
USB / SD
PLAY
PAUSE
1 ... 9, 0
SKIP
FOLDER
MUTE
RANDOM
RAND
REPEAT
INTRO
PLAY 1
A-B
ID 3
PROG
STOP
Audio player
Function
sliding switch on the rear:
AUTO PLAY = The replay will start
automatically after the unit has been
switched on
NORMAL = The unit will be set to

pause after the unit has been
switched on
RANDOM / AUTO PLAY = Replay in
random order will start automatically
after the unit has been switched on
to switch between USB port and
 
memory card

to start the replay and to switch

between replay and pause
direct title selection, examples:
title 8 = buttons 8 and PLAY

title 30 = buttons 3, 0 and PLAY
title 125 = buttons 1, 2, 5 and PLAY
beginning of title, previous / next title:

Press button briefly.

fast forward / reverse: Keep button
pressed (sound muted in the process).
to go to the first title of the previous /
 
next folder
 to mute and unmute the sound

to activate and deactivate the replay

in random order
to select the repeat function:
PLAY ALL RANDOM
the titles will be replayed once in
random order
REPEAT TRACK
the title will be repeated continuously
REPEAT FOLDER
 
all titles in the folder selected will be
repeated continuously
REPEAT ALL
all titles will be repeated continuously
RANDOM REPEAT
all titles will be replayed continuously
in random order
PLAY ALL
= function deactivated
to activate and deactivate the intro

function (The first 10 seconds of
each title are replayed.)
1Ɗ
single title replay (indication
At the end of a title, the player is set
 
to pause. To start the next title, press
the button / PLAY PAUSE.
repeat of title section
(continuous loop)
Press button at the beginning and at
 
the end of the section.
Press button once again to exit the
loop.
to switch the indication between title

information and storage device
USB CARD
selected ( / )
to program an individual title
sequence:
1. Press the button PROG.
2. Enter the folder number and press
the button PROG.
3. Enter the title number and press
 
the button PROG.
4. Repeat these steps to program all
further titles (64 max.).
5. Press the button to start the
replay.
To delete or cancel the sequence,
press the button / STOP.
to stop the replay; the display will

indicate the storage device selected,

the number of folders and titles
GB
):
9