Led Lenser SEO 3 Instrucciones De Uso página 4

LED LENSER® * SEO 3
5.2 Light Program "Red Night Vision"
If the Lighting Program "Red Night Vision" is
enabled (see Point 5), you can use the red light of
the head lamp.
When the switch button is pressed, when the SEO
3 is off, the head lamp glows in the Light Function
Power at full brightness in red. When you switch a
second time within 2 seconds, the SEO 3 blinks in
the Light Function Signal (slow even flashing).
The Light Function Signal is the last Light Function
that can be used in the Light Program "Red Night
Vision" so additional switching turns SEO 3 off
and the circle starts again with the Light Function
Power when you press the switch button again.
So the Light Functions are in a loop. But please
note that you turn off the head lamp by every
switching if since the previous switching more
than 2 seconds have elapsed. For example in case
you let pass more than 2 seconds after you turned
the Light Function Power on the next switching
will not change to head lamp to Light Function
Signal but will turn the SEO 3 off.
6. "Transport Lock"
Under Point 5 it has been described how to
switch between the white and the red LED. This
takes place when the SEO 3 is off and the switch
button is pressed only for approx. 2 seconds.
The head lamp will change from red to white
or from white to red. But when the switch is
pressed longer (approx. 5 seconds) until the
light turns off you have enabled the "Transport
Lock". Then the SEO 3 can not be turned on again
but the red LED flashes for a short moment to
indicate that this function is activated in case the
switch button is pressed. The SEO 3 therefore
cannot be switched on, either intentionally or
unintentionally and inadvertently consume
energy.
Only when you hold the switch button pressed
for 5 seconds again this function ("Transport
Lock") is deactivated again and the lamp is in the
Light Program White.
7. Reset function
If the used alkaline batteries are taken out the
battery box you have "reset" the SEO 3. You have
thus reset two functions:
- The "Transport Lock" (s. Point 6) is deactivated
- The Light Program White (s. Point 5) is activated
8. Use of rechargeable batteries
Only use 3 x Alkaline battery AAA/LR03/Micro
(1.5 V DC) or 3 x NiMH-Accumulator AAA/LR03/
Micro (1.2 V DC) in your SEO 3. Please change
all alkaline batteries respectively rechargeable
batteries (i.e. accumulators) in time.
The scope of delivery of the SEO 3 includes
alkaline batteries. This type of battery cannot be
charged resp. recharged.
9. Changing of the batteries / accumulators
Prior to the change, please turn off the SEO 3.
On the wide side of the head lamp housing is the
cover of the battery box. Nearby the switch button
there is a plastic lip. If this lip is carefully pressed
a little with e.g. your thumb up a little, the battery
box cover can be folded down by using the small
notches that are to the left and the right of the
switch button.
You can now remove the Alkaline batteries
respectively NiMH-Accumulator and insert new
ones.
During insertion, it is vital the batteries point
4
in the right direction. Therefore, pay attention
to the polarities (+ and -). Both in the battery
box and also on the batteries / accumulators.
Otherwise, the hypothetical risk that batteries or
accumulators are damaged and may explode.
After replacing the cover of the battery box has to
be closed again.
Note – Please ensure that there is no short-
circuit at the contacts of the batteries. The
contacts of the batteries may not be touched
with moist or metallic objects.
10. Headband
If the headband is not already connected to the lamp
unit, proceed as follows.
Thread the end of headband with the narrow plastic
part from the front through the eyelet on the left side
of the head lamp housing. Note the orientation of the
lettering on the headband. Run the headband then
over the cover of the battery box to the eyelet on the
other side of the battery box and run it through it to
the front.
This end of the headband has got to be pulled
through the hole beside the clipper at the plastic
part on the other side of the headband. This elongate
hole has got 4 small bars through which the narrow
plastic part has to be run from the side.
This allows that the complete end is pulled through
this hole and both ends of the headband are
connected to each other.
By using the eye of the clipper the SEO 3 can e.g.
attached to an ear of a belt or a backpack for
transportation.
The third plastic component at the headband can be
used to adjust the length of the headband in order to
fit different head circumferences.
11. Rechargeable batteries / Accumulators
Non rechargeable batteries (e.g. Alkaline batteries)
are not allowed to be charged. Never use non
rechargeable batteries and accumulators together.
Change always all batteries / accumulators at the
same time. Use in the SEO 3 only Alkaline batteries
AAA/LR03/Micro (1.5 V DC) or NiMH-Accumulators
AAA/LR03/Micro (1.2 V DC).
If you intend not to use the item for an extended
period, please take out the batteries respectively the
accumulators in order to avoid damage.
Discharged batteries (or accumulators – when they
can't be recharged any longer) have to be taken out
of the product and properly disposed with regards
to the national laws.
In general, for the disposal of batteries as well as
particularly for Lithium batteries, accumulators
and accumulator packs, the applicable rule is that
they may only be disposed of in discharged state
and in a technically correct manner. Additionally
before disposal it has to be ensured, by sticking
non-conducting adhesive tape over the contacts that
short-circuits are not possible.
Basically, the possibility of short-circuits of batteries
and also accumulators must be eliminated and they
may neither be opened, nor enter the human body in
any way, nor may they be thrown into a fire.
12. Cleaning
For cleaning, please use a dry, lint-free, clean cloth.
If salt water is spilled on the head lamp, it must be
immediately entirely removed with such a cloth.
The headband can be washed in a washing machine
at 30 °C.