Operating Elements And Connections; Infrared Remote Control - IMG STAGELINE PARL-12RGBW Manual De Instrucciones

Contents
GB
1 Operating Elements and Connections . 12
1.1 Infrared remote control . . . . . . . . . . . . . . . 12
2 Safety Notes . . . . . . . . . . . . . . . . . . . . . . 13
3 Applications . . . . . . . . . . . . . . . . . . . . . . . 13
4 Installation . . . . . . . . . . . . . . . . . . . . . . . . 13
5 Setting into Operation . . . . . . . . . . . . . . 14
6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 Remote control . . . . . . . . . . . . . . . . . . . . . 14
6.2 Operation by means of the menu . . . . . . . 14
7 Operation without DMX Controller . . . . 15
7.1 Colour spotlight and stroboscope . . . . . . . 15
7.2 Automatic programs . . . . . . . . . . . . . . . . . 15
7.3 Music control . . . . . . . . . . . . . . . . . . . . . . . 15
7.4 Master/slave mode . . . . . . . . . . . . . . . . . . 16
8 DMX Control . . . . . . . . . . . . . . . . . . . . . . 16
8.1 DMX connection . . . . . . . . . . . . . . . . . . . . 16
8.2 Setting the number of DMX channels . . . . 16
8.3 Setting the start address . . . . . . . . . . . . . . 16
9 Additional Functions . . . . . . . . . . . . . . . 17
9.1 Switching off the IR receiver . . . . . . . . . . . 17
9.2 Showing the firmware version . . . . . . . . . . 17
10 Specifications . . . . . . . . . . . . . . . . . . . . . 17
10.1 DMX functions . . . . . . . . . . . . . . . . . . . . . . 18
10.1.1 1-channel mode . . . . . . . . . . . . . . . . . . . 18
10.1.2 4-channel mode . . . . . . . . . . . . . . . . . . . 18
10.1.3 5-channel mode . . . . . . . . . . . . . . . . . . . 18
10.1.4 8-channel mode . . . . . . . . . . . . . . . . . . . 18
10.2 Menu structure . . . . . . . . . . . . . . . . . . . . . 19
12
All operating elements and connections de -
scribed can be found on the fold-out page 3.
1 Operating Elements
and Connections
1 Mains jack POWER IN for connection to a
socket (230 V~ / 50 Hz) via the mains cable pro-
vided
2 Support for the mains fuse
Always replace a blown fuse by one of the same
type.
3 Mounting brackets
4 DMX signal input (3 poles, XLR) to connect a
light controller;
pin 1 = ground, 2 = DMX−, 3 = DMX+
5 Setscrews for the mounting brackets
6 Microphone for music control
7 Control buttons
Button MENU to exit a submenu
Buttons UP and DOWN to select a menu item
and to change a setting
Button ENTER to call up a menu item, to go to
the next parameter and to save a setting
8 Display
9 Mains output jack POWER OUT for connection
of another light effect unit
10 DMX signal output (3 poles, XLR) for connec-
tion to the DMX input of another DMX light effect
unit;
pin 1 = ground, 2 = DMX−, 3 = DMX+
1.1 Infrared remote control (fig. 2)
Button
switch all LEDs off and on again
DMX mode, input of the DMX start address
DMX
with the number buttons (3 digits)
SLAVE switch slave mode on
AUTO 1/ 2 automatic programs 1 and 2
set the speed of the programs 1/ 2 with the
SPEED
buttons UP/ DOWN
switch on music control 1 or 2, change micro-
SOUND 1/ 2
phone sensitivity with UP/ DOWN
speed of the programs 1/ 2, stroboscope fre-
UP, DOWN
quency, brightness, microphone sensitivity
STROBE switch stroboscope on and off
switch primary colours red, green and blue as
well as white for colour spotlight or strobo-
R, G, B, W
scope on and off, change the brightness with
UP/ DOWN
Function