Setting The Transmission Frequency; Remoset ® Function - Monacor JTS UF-10TH/12 Manual De Instrucciones

4.5 Setting the transmission frequency

Before switching on the microphone, set the
receiver to an interference-free frequency (see
instruction manual of the receiver). Then set the
microphone to the same frequency: There are
three methods to do this:
1. If you operate the microphone with the receiver
UF-10R /12, the easiest way is to use the
patented REMOSET function. When you press
the button REMOSET on the receiver, the
microphone is set to the transmission frequency
selected on the receiver (chapter 4.5.1).
2. The transmission frequency can be adjusted man-
ually between 624.000 MHz and 693.975 MHz
(chapter 4.5.2).
3. For operating several audio transmission sys-
tems at the same time, there are 12 groups with
up to 60 channels in each group (
page 28, 29). In ideal conditions, up to 40 chan-
nels from a group can be used for audio trans-
mission at the same time. If the receiver has
been set to a channel from these groups, select
the same channel for the microphone (chap -
ter 4.5.3).
4.5.1 REMOSET ® function
For the REMOSET function always make sure that
1. no menu is called up on the receiver or on the
transmitter.
2. the microphone is switched on and close to
the receiver (REMOSET transmission range:
approx. 10 m).
3. the microphone and the receiver are set to the
same identification number (ID No.) or that the
function ID No. is deactivated (see paragraph
"Identification number").
4. the REMOSET function is not deactivated (see
paragraph "Deactivating the REMOSET
tion").
5. the receiver and the transmitter are not locked
( chapter 4.9).
6. the signal LED (2) does not flash. If it keeps
flashing, the microphone is muted. In this case,
press the button
guished.
table on
®
(1) so that the LED is extin-
Identification number
To prevent mutual interference of individual pairs of
microphone / receiver during REMOSET transmis-
sion, each pair must have a different identification
number (ID No.). If you only use one pair of micro-
phone / receiver, there is no need to change the pre-
set ID No. 0. To change the ID No.:
1) Call up the setting for the ID No. via the menu
Device ID
item
Device ID
0
ID : ON
2) Press the button ▼ or ▲ to set the ID No.
3) Press the button SET. Then press the button ▼
to deactivate the function (OFF) or the button ▲
to activate the function (ON). If the function has
been deactivated, the REMOSET transmission
will be possible from any UF-10R /12 receiver; if
it has been activated, the REMOSET transmis-
sion will only be possible from a receiver with
the same ID No.
4) Press the button SET to save the setting.
REMOSET ® transmission
Press the button REMOSET on the receiver. As
soon as the microphone has been set to the trans-
mission frequency or to the group and the trans-
mission channel of the receiver, the signal LED (2)
shows blue for five seconds.
If the signal LED does not light up, the auto-
matic synchronization of the microphone has failed.
In this case, the button REMOSET on the receiver
keeps flashing slowly. For troubleshooting see
steps 1 – 6 at the beginning of this chapter. Check
the settings on the microphone and possibly on the
transmitter and correct them. Then press the button
REMOSET on the receiver again.
func-
Deactivating the REMOSET
The REMOSET function can be deactivated to pre-
vent automatic frequency setting.
1) Call up the menu item
menu.
Remote Set
ON
OFF
2) Press the button ▼ to deactivate the function
(OFF) or the button ▲ to activate it (ON).
3) Press the button SET to save the setting.
of the main menu.
Fig. 7
® function
Remoset
in the main
Fig. 8
13