Makita DSL800 Manual De Instrucciones página 13

NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overload protection
When the tool or battery is operated in a manner that
causes it to draw an abnormally high current, the tool
automatically stops and the lamp blinks. In this sit-
uation, turn the tool off and stop the application that
caused the tool to become overloaded. Then turn the
tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically and the lamp lights up. In this case, let the
tool and battery cool before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
Switch action
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION:
Switch can be locked in "ON" posi-
tion for ease of operator comfort during extended
use. Apply caution when locking tool in "ON"
position and maintain firm grasp on tool.
CAUTION:
Do not install the battery cartridge
with the lock button engaged.
CAUTION:
When not operating the tool,
depress the trigger-lock button from
lock the switch trigger in the OFF position.
► Fig.3: 1. Trigger-lock button
► Fig.4: 1. Switch trigger 2. Lock button 3. Trigger-
lock button
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided. To start the tool,
depress the trigger-lock button from A (
the switch trigger. Release the switch trigger to stop.
After use, depress the trigger-lock button from B ( )
side.
For continuous operation, depress the lock button while
pulling the switch trigger, and then release the switch
trigger. To stop the tool, pull the switch trigger fully, then
release it.
Speed adjusting dial
► Fig.5: 1. Speed adjusting dial
The rotation speed of the tool can be changed by turn-
ing the speed adjusting dial. The table below shows
the number on the dial and the corresponding rotation
speed.
Number
1
2
3
4
5
NOTICE:
to "1", turn the dial counterclockwise. Do not turn
the dial clockwise forcibly.
Overload and overheat indicator
lamp
► Fig.6: 1. Indicator lamp
If the tool is operated with excessive load, the tool stops
automatically and the indicator lamp blinks in red. In this
case, reduce the load on the tool.
If the tool is overheated, the tool stops automatically
and the indicator lamp lights up in red. In this case, let
the tool cool down before turning the tool on again.
Electronic function
The tools equipped with electronic function are easy to
operate because of the following features.
Constant speed control
Possible to get fine finish, because the rotating speed is
kept constant even under the loaded condition.
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
side to
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Assembling the tool bag
) side and pull
1.
► Fig.7
2.
► Fig.8: 1. Tool bag
3.
the inner tray with hook and loop fastener as shown in
the figure.
► Fig.9: 1. Hook and loop fastener 2. Inner tray
13 ENGLISH
When changing the speed dial from "5"
Always be sure that the tool is
Take out the tool and the tool bag from the box.
Unfold the tool bag.
Insert the inner tray into the tool bag, and then fix
Speed
-1
1,000 min
-1
1,200 min
-1
1,400 min
-1
1,600 min
-1
1,800 min