Makita RT0700C Manual De Instrucciones página 12

ENGLISH
(Original instructions)
1 Bit protrusion
2 Tool base
3 Scale
4 Locking lever
5 Adjusting screw
6 Hex nut
7 Switch
8 OFF (O) side
9 ON ( I ) side
10 Speed adjusting dial
11 Tighten
12 Loosen
13 Hold
14 Shaft lock
15 Workpiece
16 Bit revolving direction
17 View from the top of the tool
18 Feed direction
19 Straight guide
20 Base protector
21 Screws
22 Screwdriver
23 Straight bit
24 Base
25 Templet
26 Distance (X)
27 Templet guide 10
28 Base protector
SPECIFICATIONS
Model
Collet chuck capacity.................6 mm, 8 mm, 1/4" or 3/8"
-1
No load speed (min ) ............................ 10,000 – 30,000
Overall length ...................................................... 200 mm
Net weight .............................................................. 1.8 kg
Safety class .............................................................
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
12
Explanation of general view
29 Bolt
30 Guide plate
31 Wing nut
32 Clamp screw (A)
33 Center hole
34 Nail
35 Clamp screw (A)
36 Adjusting screw
37 Clamp screw (B)
38 Trimmer guide
39 Bit
40 Guide roller
41 Clamping screws
42 Base protector
43 Screw
44 Pulley
45 Collet nut
46 Collet cone
47 Wrench
48 Belt
49 Locking lever
50 Offset base
51 Hex wrench
52 Offset base plate
53 Upper section of the offset base
54 Bar type grip (optional acces-
sory)
General Power Tool Safety Warnings
RT0700C
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
/II
Save all warnings and instructions for future refer-
ence.
TRIMMER SAFETY WARNINGS
1.
ENE010-1
2.
ENF002-1
3.
4.
5.
6.
7.
8.
9.
55 Grip attachment (optional
accessory)
56 Trimmer base
57 Knob type grip
58 Plunge base
59 Grip
60 Knob
61 Adjusting knob
62 Lock lever
63 Depth pointer
64 Stopper pole setting nut
65 Fast-feed button
66 Stopper pole
67 Stopper block
68 Adjusting bolt
69 Guide holder
70 Wing bolts
71 Guide bar
72 Wing bolt
73 Outside diameter of the templet
guide
74 Templet guide
75 Dust nozzle
76 Thumb screw
77 Limit mark
78 Brush holder cap
WARNING Read all safety warnings and all
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
Wear hearing protection during extended period
of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
GEA010-1
GEB019-4