Publicidad
Factory setting / Manual programming
EN
5 mm
Stagnationsspülung
tagnationsspülung
ng
Spüldauer
püldauer
2
Reinigungsstopp
einigungsstopp
1
10 mm
10 mm
10 mm
Geruchverschlussspülung
eruchverschlussspülung
spülung
Stadionbetrieb
tadionbetrieb
5 mm
5 mm
5 mm
Reichweiteneinstellung
eichweiteneinstellung
F1
ellung
F2
Vorspülung
orspülung
F3
Datum
Datum
F4
* Factory setting
Bemerkungen
** Programming example
emerkungen
1 : 1
1 : 1
Programming is carried out in four steps, which are briefly summarised
here.
1.
Start manual programming
Disconnect the power supply — wait at least 20 s — and reconnect the
power supply.
When the electronics are booting, the LED in the sensor field flashes red/
yellow.
Do not put your hands into the sensor area during this phase!
Afterwards the LED is red for max. 7 s. During this red phase, cover the
sensor field and keep it covered. Programming mode is started.
2.
Select function (F1 - F3)
The functions are now indicated one at a time by the flashing yellow LED
(see table).
To select a function, uncover the sensor field when the corresponding
code is flashing.
1 : 1
1 : 1
1 : 1
5 mm
Zustand der Armatur
Wasser läuft
5 mm
Kein Wasser
Wenig Wasser
~ 10 mm
Zustand der Armatur
Zustand der Armatur
Zustand der Armatur
Wasser läuft
Wasser läuft
Kein Wasser
Wasser läuft
Kein Wasser
Wenig Wasser
Kein Wasser
Wenig Wasser
Parameter:
Wenig Wasser
kurz
Range
mittel
lang
Stagnation flush
Thermal disinfection or
Permanent flow
Cleaning stop
1 : 1
1 : 1
1 : 1
kurz
1 : 1
kurz
kurz
mittel
mittel
lang
mittel
lang
lang
1 : 1
1 : 1
1 : 1
5 mm
Kein Wasser
Wasser läuft
Wenig Wasser
Kein Wasser
Wenig Wasser
Manual programming
Operating elements for programming:
1 LED (yellow / red)
2 Lower sensor area
Attention! For manual programming, always cover the upper (1) and
lower (2) sensor area at a distance of approx. 10 mm!
The following table provides an overview of the main programs and the
available parameters for programming the fitting manually:
P1
Short
kurz
mittel
Off *
lang
Off *
Off *
In the pictures from page 2 4 , manual programming is
depicted step-by-step.
As an example it is shown how to set the "range" func-
tion (F1) to "long" (P3).
1 : 1
3.
Set parameters
The flashing red LED shows you the currently set parameter (see table).
By covering the sensor field again you can set the corresponding para-
meter. The parameters are indicated one at a time by the flashing red
LED (see table).
To set a parameter, uncover the sensor area when the corresponding
code is flashing.
4.
Start operation
After leaving the sensor field, the programming mode starts once again
with a time window of 7 seconds (red LED is on continuously).
If the sensor field is not covered during these 7 seconds, the program-
ming is completed. The fitting is now ready for use.
Wenig Wasser
P2
P3
kurz
mittel
kurz
Medium *
lang
mittel
lang
On,
On, 24 h after last use
daily every 24 h
On, TD 300 s
On, 120 s
On, 60 s
---
1 : 1
Long **
15
Publicidad
